Search found 199 matches

by jmp
Wed Mar 21, 2018 2:40 pm
Forum: Printing Settings
Topic: Adhesion Issues
Replies: 18
Views: 430

Re: Adhesion Issues

A picture of what you are seeing would be very helpful for us in trouble shooting. I sometimes see this when I am over extruding or have the bed to close to the nozzle for the first layer (the plastic has no where to go so it pushes up the plastic laid down next to it causing the waves).
by jmp
Mon Feb 19, 2018 2:29 pm
Forum: Software
Topic: Limitations of spiral/vase mode
Replies: 5
Views: 196

Re: Limitations of spiral/vase mode

In my experience up to 45 degrees should be no problem, 45-60 usually OK, over 60 depends on filament, temperature, layer height and what not.

I believe you can specify at what angle you want supports in ideamaker, of course you can't use supports in spiral mode.
by jmp
Sun Feb 04, 2018 7:48 pm
Forum: Software
Topic: Problem with retract
Replies: 5
Views: 223

Re: Problem with retract

I'm having the same issue on my N2+. I don't know when it started and I haven't spent much effort figuring out the why but I am also getting the retract on every begin and end line.
by jmp
Sun Feb 04, 2018 7:42 pm
Forum: Software
Topic: First layer height - can we get it in %?
Replies: 2
Views: 129

Re: First layer height - can we get it in %?

For me the % in S3D is actually a problem. This just happened to me yesterday I changed the layer thickness from .1 to .2 but forgot I had my first layer height at 200% and a first layer height of 0.4 didn't work out to well.
by jmp
Tue Jan 30, 2018 5:30 pm
Forum: General
Topic: Who's going to MRRF this year?
Replies: 1
Views: 188

Re: Who's going to MRRF this year?

I will be going again this year. Might bring my Palette depending on what else I am bringing. The N2+ will be staying home :)
If they were smart Raise 3D would get a table, it really is about the biggest event specifically about 3D printing in the US.
by jmp
Thu Jan 04, 2018 12:53 pm
Forum: Printing Settings
Topic: Problems with PLA
Replies: 9
Views: 582

Re: Problems with PLA

I tried with 60°C and the print went well. Just for my understanding ... as answered by Vicky and 3Dnoob, in the Internet someone say to increase the temperature to 60°C and someone says to turn it off . For a newbie like me is a little bit confusing ... it depends only on the presence or absence o...
by jmp
Wed Jan 03, 2018 7:01 pm
Forum: Hardware
Topic: Touch screen freezing
Replies: 17
Views: 1102

Re: Touch screen freezing

Hi, Jason. I got the same situation as you mentioned. I was told to have my screen box replaced, too. But the new circuit board was not really the same as the original one. And the technician told me to connect the 24v wire to the PSU(the green one). But then when I plugged in electricity, it blew ...
by jmp
Fri Dec 22, 2017 3:30 pm
Forum: General
Topic: Surface quality on tall prints
Replies: 17
Views: 1528

Re: Surface quality on tall prints

Hi Michael, I have attached a 300mm tall piece of baseboard that was printed vertically where the problem slowly presents itself the farther up it goes. All doors were open including the side and top lid removed. No difference for me either way. Something that tall and thin is going to sway a littl...
by jmp
Mon Dec 11, 2017 12:53 am
Forum: Hardware
Topic: glass bed can't be leveled because it's not flat :/
Replies: 13
Views: 807

Re: glass bed can't be leveled because it's not flat :/

After spending the good part of a day trying to level the bed (high spot in the middle), I realized that it wasn't possible when looking at the bed from the side, I noticed that the glass was not in contact with the platform in the middle. Logically, if the glass is clamped on the sides and the mid...
by jmp
Fri Dec 08, 2017 1:13 pm
Forum: General
Topic: access files on local drive
Replies: 6
Views: 335

Re: access files on local drive

I have a N2 plus dual and I have a file saved on the local drive that I would like to download and edit on my laptop. How do I gain access to that code once it is uploaded? I've tried copying or moving the file but that only allows you to do so in the same directory. I'm not at my printer at the mo...
by jmp
Sat Dec 02, 2017 12:25 am
Forum: Software
Topic: issue uploading gcode (ideaMaker 3.0)
Replies: 25
Views: 1079

Re: issue uploading gcode (ideaMaker 3.0)

I just tried with WinSCP, a 50mb gcode file took 10 minutes to upload so the issue also appears outside of ideaMaker.
by jmp
Thu Nov 30, 2017 1:26 pm
Forum: Software
Topic: Simplify3D vs IdeaMaker3 - your opinion?
Replies: 7
Views: 573

Re: Simplify3D vs IdeaMaker3 - your opinion?

I have had S3D for over 4 years now and have used it on the Raise3D. IdeaMaker is actually a pretty good slicer. I find unless I am doing something pretty complicated that requires a specific feature of S3D I default to Ideamaker because it is both designed for the printer and the convenience of upl...
by jmp
Wed Nov 29, 2017 2:48 pm
Forum: Software
Topic: issue uploading gcode (ideaMaker 3.0)
Replies: 25
Views: 1079

Re: issue uploading gcode (ideaMaker 3.0)

Have you ever tested with the following steps? I have turned the wifi off on the printer. As for the other steps I think its a bit much to need to hard code all the IP address on my home network (my router defaults to a 192.168.10.* address) to see if that fixes the issue. I'll put up with it worki...
by jmp
Tue Nov 28, 2017 4:52 pm
Forum: Software
Topic: issue uploading gcode (ideaMaker 3.0)
Replies: 25
Views: 1079

Re: issue uploading gcode (ideaMaker 3.0)

Vicky@Raise3D wrote:And also no change with the new touch panel being replaced?

No, same behavior with the old and the new touch panel. With the old touch panel I had the cord plugged into the back of the machine, with the new panel it is plugged directly to the panel.
by jmp
Tue Nov 28, 2017 12:01 am
Forum: Software
Topic: issue uploading gcode (ideaMaker 3.0)
Replies: 25
Views: 1079

Re: issue uploading gcode (ideaMaker 3.0)

If you have to use LAN, please try connect to the LAN slot on touchscreen directly and see if that works better. It may be the problem of the extension cable to the back. Just to add a data point. I too have had slow transfers via Ethernet. I recently had to replace the touch panel so while everyth...
by jmp
Sun Nov 05, 2017 12:00 am
Forum: General
Topic: Bond Tech Extruders . Any good, whats the improvement?
Replies: 17
Views: 1461

Re: Bond Tech Extruders . Any good, whats the improvement?

The installation is pretty simple, probably can be done in an hour even if being really careful (there is a video showing step by step installation). I first upgraded to the bondtech that reused the original motor and it worked flawlessly for a year and about 2000 print hours. I just installed the B...
by jmp
Sat Oct 28, 2017 10:27 am
Forum: Hardware
Topic: Touch screen freezing
Replies: 17
Views: 1102

Re: Touch screen freezing

There is likely a ton of length on that wire bundled in the base of the machine VS soldering. Normally I would do this except I have the N2+ and I figured I would much more likely damage the printer trying to tip that beast over to access the bottom than any issues from extending the wires. If at a...
by jmp
Wed Oct 25, 2017 4:23 pm
Forum: Hardware
Topic: Touch screen freezing
Replies: 17
Views: 1102

Re: Touch screen freezing

I got a call from tech support on Monday explaining what I needed to do (which matched up with what you said). Went to connect the wires yesterday and because the wire terminal is higher than were the plug was on the V1 board the wires were not long enough. I was a bit frustrated so I walked away fr...
by jmp
Mon Oct 23, 2017 1:38 am
Forum: Hardware
Topic: Touch screen freezing
Replies: 17
Views: 1102

Re: Touch screen freezing

Jetguy- Thanks for the detailed explanation. Definitely glad I didn't do any guessing. I think I know what I need to do but since I am already out $450 for the first replacement I am going to wait for an official response to my support ticket so that any possible mistake with this new board isn't mi...

Go to advanced search