Search found 15 matches

by Ari
Sun Jul 02, 2017 1:50 pm
Forum: Hardware
Topic: N2 Plus Casters (Wheels) Can't Swivel 360
Replies: 19
Views: 434

Re: N2 Plus Casters (Wheels) Can't Swivel 360

@jamma

Bad luck with the new floors :cry:. You could always print yourself a nice set of spacers to provide clearance for the castors and then reclaim your washers.

Ari
by Ari
Wed May 10, 2017 3:31 pm
Forum: Feature requests, ideas, wishes
Topic: Make changes available - rant warning
Replies: 11
Views: 607

Re: Make changes available - rant warning

Dear Vicky, Regarding your statement -"For open source, we haven't promised open source before." The published Raise3D kickstarter brochure implies that the printer is open source. i.e. "We will publish our APIs and toolchains after the Kickstarter campaign’s conclusion". Brochur...
by Ari
Mon May 08, 2017 9:37 pm
Forum: Printing Software
Topic: Conducting Filament
Replies: 20
Views: 1321

Re: Conducting Filament

An interesting experiment. Given current progress in the technology of conductive filament I think that is not too bad a result. Perhaps to better demonstrate the concept to your students you could increase the voltage to make the LED appear brighter. Some of the later type LEDs are quite bright whe...
by Ari
Sat Mar 11, 2017 12:04 pm
Forum: Hardware
Topic: What sealant should be used
Replies: 6
Views: 433

Re: What sealant should be used

The raise3d hot end assembly instructions refer to high temperature silicon grease (not a sealant). Presumably this is to make it easier to release the threads of the throat tube the next time it needs to be removed.
by Ari
Wed Feb 01, 2017 8:06 am
Forum: Hardware
Topic: V2H Nozzles Swap & Adjustment
Replies: 2
Views: 245

Re: V2H Nozzles Swap & Adjustment

The distance between the nozzle and the platform can be adjusted by turning the thumb screw on the left-front corner of the Z plate. The higher the screw stands out, the further the distance between nozzle to the print platform gets. "https://cdn.shopify.com/s/files/1/1312/8511/files/leveling.p...
by Ari
Sun Jan 29, 2017 8:30 pm
Forum: Hardware
Topic: Are Raise3D printers upgradable from single to dual extruders?
Replies: 5
Views: 359

Re: Are Raise3D printers upgradable from single to dual extruders?

JClay - You are right only part of the link was shown. - Sorry

It should have been;

"http://forum.raise3d.com/viewtopic.php?t=1172"
by Ari
Sun Jan 29, 2017 5:59 pm
Forum: Hardware
Topic: Are Raise3D printers upgradable from single to dual extruders?
Replies: 5
Views: 359

Re: Are Raise3D printers upgradable from single to dual extruders?

Vicky might want to reply directly, but in the meantime you could take a look at her answer in the thread linked below;

viewtopic.php?t=1172
by Ari
Sun Jan 29, 2017 3:59 pm
Forum: Hardware
Topic: Tightening belts
Replies: 18
Views: 1295

Re: Tightening belts

Wish the timing belt on my car wouldn’t stretch, then I wouldn’t need to cough up loads of $$ every four years or so? - granted, these printers are not operating under torque. ;) Jetguy – Sure, what you have written is sound advice, I guess not everyone is comfortable taking their printer apart and ...
by Ari
Sun Jan 29, 2017 1:32 pm
Forum: Hardware
Topic: Tightening belts
Replies: 18
Views: 1295

Re: Tightening belts

I could imagine that over time with the cyclic heating and cooling effects of using the printer, the belts will require some adjustment. Although I have not had my N2 long enough yet to find out.

@ABH Thanks for posting your tool. It will come in useful.
by Ari
Sat Jan 28, 2017 7:36 am
Forum: Hardware
Topic: Tightening belts
Replies: 18
Views: 1295

Re: Tightening belts

@RaiserDog – Maybe the attached will help. Source = Raise3D

Regards

Ari
by Ari
Sat Jan 14, 2017 6:03 pm
Forum: Hardware
Topic: Availability of replacement touch screen controllers
Replies: 4
Views: 356

Re: Availability of replacement touch screen controllers

Hello Vicky,

Thank you very much for the update. Today I received confirmation that the replacement has arrived at iMakr in the UK.

Hopefully I will receive it next week.

I am happy now :D
by Ari
Fri Jan 13, 2017 1:28 pm
Forum: Hardware
Topic: Availability of replacement touch screen controllers
Replies: 4
Views: 356

Re: Availability of replacement touch screen controllers

Dear Vicky, Thank you for the reassurance that shipment of my replacement controller has been arranged :). However, I still do not have an expected delivery date, which I need so that I can advise my customer when I might be able to complete his order. :cry: I was half way through a print when the c...
by Ari
Fri Jan 13, 2017 12:06 am
Forum: Hardware
Topic: Availability of replacement touch screen controllers
Replies: 4
Views: 356

Availability of replacement touch screen controllers

Hello Vicky, Since you visit the forum regularly would you please check the availability of replacement touch screen controllers. Mine failed towards the end of December last year and I raised a support ticket (#648 "N2 Printer will not boot-up"). It was agreed that my controller PCB would...
by Ari
Sat Dec 24, 2016 11:19 am
Forum: Hardware
Topic: Back-up Battery
Replies: 2
Views: 302

Re: Back-up Battery

Thank you Vicky :D
by Ari
Fri Dec 23, 2016 3:22 pm
Forum: Hardware
Topic: Back-up Battery
Replies: 2
Views: 302

Back-up Battery

Does anyone know the capacity (in mAh) of the 3.7V back-up battery used on the N2 :?:

Go to advanced search