Search found 40 matches

by Ben Roj
Mon Apr 23, 2018 1:04 pm
Forum: General
Topic: Just Released N2 Pro
Replies: 112
Views: 3834

Re: Just Released N2 Pro

Now Ultimaker S5 show all the details and I will say that Pro2 Plus seem like a better value on the paper. They are almost same price USD5,999 (r) vs USD5,995 (u), different build volume 280x305x605 (r) vs 330x240x300mm (u) Ultimaker S5 come with various swap-able print heads and 2 types of print be...
by Ben Roj
Mon Apr 23, 2018 7:18 am
Forum: General
Topic: Just Released N2 Pro
Replies: 112
Views: 3834

Re: Just Released N2 Pro

I had seen BCN3D Sigmax dual printing and I like the feature when dual printing, the unused nozzle will have temperature drop down to around 150-160c to minimized the oozing and kickback when it is about to switch back to do the printing. Though this might not work for Raise3D Pro2 as it is not Inde...
by Ben Roj
Wed Apr 18, 2018 4:53 am
Forum: General
Topic: Just Released N2 Pro
Replies: 112
Views: 3834

Re: Just Released N2 Pro

Thank you vicky for the info. Glad to know that these sockets will come as standard part now. Matterhacker has the new pro2 demo unit on display now. If anyone has a chance to visit them, might want to check it out. https://www.youtube.com/watch?v=OK_cm8eobCk Does anyone know where I can get the sil...
by Ben Roj
Tue Apr 17, 2018 5:22 pm
Forum: General
Topic: Just Released N2 Pro
Replies: 112
Views: 3834

Re: Just Released N2 Pro

I heard from local reseller that Ultimaker is releasing Ultimaker 3 XL with 30x30x30cm build area soon. How soon will that be? I think it is this one, bigger Ultimaker 3 https://www.youtube.com/watch?v=5mCzTBFDyBg Thank Jetguy for the screenshot, the insulator socket has raise3D logo stamp on it, h...
by Ben Roj
Mon Apr 16, 2018 11:02 am
Forum: General
Topic: Just Released N2 Pro
Replies: 112
Views: 3834

Re: Just Released N2 Pro

Matterhacker has the new pro2 demo unit on display now. If anyone has a chance to visit them, might want to check it out.

https://www.youtube.com/watch?v=OK_cm8eobCk


Does anyone know where I can get the silicone sockets shown in the video?
by Ben Roj
Tue Apr 03, 2018 6:24 am
Forum: General
Topic: Just Released N2 Pro
Replies: 112
Views: 3834

Re: Just Released N2 Pro

I heard from local reseller that Ultimaker is releasing Ultimaker 3 XL with 30x30x30cm build area soon. I agree that it will be a pain to disassemble the new pro extruder when get the filament jam, just look at all the cables and parts (filament sensor) and small servo motor to control the dual extr...
by Ben Roj
Sat Aug 19, 2017 9:17 pm
Forum: Printing Settings
Topic: Standard R3D PLA
Replies: 16
Views: 1517

Re: Standard R3D PLA

Do you use the guide tube that come with the machine? Remove that if you do. Also, several time the extrusion get into issue due to the way filament spool holder locate. If possible try to put filament spool on top of the printer and let the gravity help to pull it down straight into the extruder.
by Ben Roj
Fri Jul 14, 2017 2:39 pm
Forum: Software
Topic: Marlin 1.1.0 Unofficial firmware version 1.2.1
Replies: 19
Views: 1415

Re: Marlin 1.1.0 Unofficial firmware version 1.2.1

It is unofficial version (testing), posted by Vicky in another topic. http://forum.raise3d.com/viewtopic.php?f=2&t=593&start=40 Where did you see this? I just checked Github and official downloads. I see your commit here https://github.com/Firesped/Marlin-Raise3D-N-Series/commits/FRS But I d...
by Ben Roj
Sun Jun 18, 2017 8:08 pm
Forum: General
Topic: Tech support unable to advise, printing ceases after 30-40 mins
Replies: 23
Views: 2928

Re: Tech support unable to advise, printing ceases after 30-40 mins

What filament PLA brand are you using? If you are sure that you measure 130c at hot end while it is printing, then you should check the wiring of thermocouple to the mini board on extruder, then try to use the 2nd thermocouple that you had prior removed to replace with the 1st one. Make sure that bo...
by Ben Roj
Mon May 15, 2017 7:04 pm
Forum: Hardware
Topic: a very very clogged hotend- advice
Replies: 5
Views: 869

Re: a very very clogged hotend- advice

I had once bigger blob than this after failed print over night for full bed size object. I didnt have the heat gun, so I just used another hotend to melt (heat up to around 150c) by pressing it into the plastic ball till it reach the metal hotend inside. Wait it to get cool down for a 30seconds, the...
by Ben Roj
Tue Apr 25, 2017 4:24 pm
Forum: General
Topic: Print stops after 30min.
Replies: 15
Views: 2400

Re: Print stops after 30min.

May I know what do you do or replace to fix this problem?
by Ben Roj
Sun Apr 23, 2017 5:26 am
Forum: Hardware
Topic: Hardware problem?
Replies: 18
Views: 1151

Re: Hardware problem?

have you check the belt tension and screw tightness on each pulley at the corners. When printing the circular, please observe what happen when printing on that defect part - any mechanic noise or unusual behaviors that you can notice? I have experience similar defect when I printed a full size circl...
by Ben Roj
Sat Apr 22, 2017 6:10 pm
Forum: Hardware
Topic: A little disappointed with the N2
Replies: 28
Views: 3174

Re: A little disappointed with the N2

That is exactly what I request them to change in the firmware, unable to turn off the LCD screen when battery is below 60-70% even when unplugged the power cable - is a very bad design. The LCD will keep flashing. The only thing you can do is to turn it on, and left it overnight. I dont want to imag...
by Ben Roj
Sat Apr 01, 2017 7:00 pm
Forum: Software
Topic: Resuming Print - N2
Replies: 4
Views: 572

Re: Resuming Print - N2

To bypass this issue, you can connect to printer via Ideamaker through wifi and adjust the setting from that mirror interface screen. I have this happened to me sometime too, but it can continue to print without problem.
by Ben Roj
Sun Mar 26, 2017 5:53 am
Forum: Others
Topic: Clogging during a print
Replies: 44
Views: 5583

Re: Clogging during a print

Most of all metal hotend will have issue with standard PLA because of constant retraction, causing filament which get soften clogged in the thermal tube. Polymaker PLA or Raise3D Premium (Polymaker OEM) have higher temp glass transition, so it can retain its form better in thermal tube. You can try ...
by Ben Roj
Thu Mar 09, 2017 3:30 pm
Forum: Hardware
Topic: Micro Swiss nozzles
Replies: 2
Views: 561

Re: Micro Swiss nozzles

What version of micro swiss do you use? I used to contact them and they said that it is commissioned by Raise3D and they can not sell it through their store.
by Ben Roj
Tue Feb 28, 2017 4:07 pm
Forum: General
Topic: What's a good reliable PLA
Replies: 18
Views: 1987

Re: What's a good reliable PLA

Polymaker is also another alternative though it is not cheap.
by Ben Roj
Fri Nov 18, 2016 2:48 pm
Forum: Hardware
Topic: n2plus y-Axe dosen´t move
Replies: 10
Views: 953

Re: n2plus y-Axe dosen´t move

Can you move extruder along Y axis by hand when the machine is turn off?
by Ben Roj
Thu Aug 18, 2016 12:41 pm
Forum: Hardware
Topic: BTSN2 Build Plate for Raise3D N2 Printers
Replies: 54
Views: 7472

Re: BTSN2 Build Plate for Raise3D N2 Printers

Hi Michael Can you upload video showing how it work, especially the part where you can bend the plate to release the print object? Does it resist to crack under pressure better than borosilicate glass? I have already break my plate while trying to remove the large print object. As you mentioned that...
by Ben Roj
Sat Aug 13, 2016 7:09 am
Forum: General
Topic: Help needed : unwanted xy translation during prints
Replies: 8
Views: 1380

Re: Help needed : unwanted xy translation during prints

You might want to try Z hop feature , it might increase the print time (the time estimation given in the slicer is way off so just ignore it) but can help to minimize collision.

Go to advanced search