Search found 412 matches

by Noren
Sun Jan 20, 2019 3:55 pm
Forum: N Series
Topic: z-banding/print surface quality
Replies: 13
Views: 290

Re: z-banding/print surface quality

Please share some images of your mod. Interesting.
by Noren
Fri Jan 18, 2019 7:46 am
Forum: N Series
Topic: Extrusion or something else?
Replies: 4
Views: 67

Re: Extrusion or something else?

Flightrider wrote:Thanks for responding @Noren....
Whatever it was, it's not doing it now! Go Figure.


:)

Could have been a partial clog.
by Noren
Thu Jan 17, 2019 11:57 am
Forum: N Series
Topic: z-banding/print surface quality
Replies: 13
Views: 290

Re: z-banding/print surface quality

Check your motor couplers.
Skärmavbild 2019-01-17 kl. 12.56.16.png
by Noren
Thu Jan 17, 2019 10:54 am
Forum: N Series
Topic: Extrusion or something else?
Replies: 4
Views: 67

Re: Extrusion or something else?

Check if your filament is feeding correctly and not slipping.
by Noren
Wed Jan 16, 2019 9:52 am
Forum: Pro2 Series
Topic: 22" tall print stopped printing at 19.75 "s
Replies: 3
Views: 83

Re: 22" tall print stopped printing at 19.75 "s

I have also noticed a large difference in calculated time and actual print time in the latest version. (I have the N1 Dual with the latest version of RaiseTouch, Motionboard and ideamaker. I have the cloud version). I have previously had pretty much bang on calculated and actual print times. But for...
by Noren
Fri Jan 11, 2019 8:36 pm
Forum: N Series
Topic: Extruder 2 Error
Replies: 2
Views: 58

Re: Extruder 2 Error

Do you have the thermal protector installed? These kind of random errors are often due to a break in the flat cable to the extrude board. The gray flat one. If you have one of the N2:s there are often extra cables bundled in the printer that you can use. Cut of the broken bit and pull out a fresh se...
by Noren
Thu Jan 10, 2019 1:52 pm
Forum: N Series
Topic: Load filament width
Replies: 1
Views: 55

Re: Load filament width

Not sure that I understand correctly?. Is the extruded plastic from the nozzle during the load cycle wider than your nozzle diameter?
If it is I would guess that you should change to a new nozzle.
by Noren
Thu Jan 10, 2019 9:47 am
Forum: Printing Settings
Topic: Any luck printing @ 0.1mm / 0.05mm layer thickness?
Replies: 3
Views: 365

Re: Any luck printing @ 0.1mm / 0.05mm layer thickness?

I only briefly tried printing with S3D on my Raise3D. But I had a hard time getting any good results. And I think that the results on the Raise3D machines with IdeaMaker is on par or better than S3D. I have also successfully printed .1 and .05 with the default High Quality templates. Correct distanc...
by Noren
Tue Jan 08, 2019 10:07 am
Forum: Pro2 Series
Topic: Cables touching Belts
Replies: 5
Views: 173

Re: Cables touching Belts

The same on my N1.
by Noren
Sat Dec 29, 2018 6:26 pm
Forum: N Series
Topic: Bondtech Dual Upgrade problem
Replies: 5
Views: 242

Re: Bondtech Dual Upgrade problem

Bad top surface is often due to the nozzle to close to the bed or overextrusion. Or a combination.
by Noren
Sat Dec 29, 2018 6:25 pm
Forum: Software
Topic: API?
Replies: 20
Views: 2146

Re: API?

jetdillo wrote:Is this available for the N2 series or just the Pro ?
I have an N2 Plus and that port isn't active on my machine. I have TouchPanel firmware version 1.1.0.1021.


You need to install the Raise Touch Cloud firmware I think.
by Noren
Fri Dec 07, 2018 11:59 am
Forum: Printing Settings
Topic: Now Support
Replies: 2
Views: 129

Re: Now Support

Chrigi78 wrote:Dear all

now we have a intressting problem

if we say no support an Make no Support the system make self support on diffrent points ???

how we can switch off this ???


Check that you have "none" selected in this menu:
Skärmavbild 2018-12-07 kl. 12.58.22.png
by Noren
Mon Dec 03, 2018 10:34 pm
Forum: Software
Topic: IM Graphic Box showing up in new release
Replies: 3
Views: 180

Re: IM Graphic Box showing up in new release

DragonXtreme wrote:Thanks Noren, unfortunately my account was deleted and all my post along with it. So now I have to make a couple more post to get back to allowed status without being monitored. Vicky gave no reason for the deletion except that it was. :(


Sorry to Hear. :(
by Noren
Sun Dec 02, 2018 11:58 am
Forum: Pro2 Series
Topic: New Firmware Settings - Which is Master?
Replies: 5
Views: 250

Re: New Firmware Settings - Which is Master?

The sethings in the printer is used if you haven’t checked the acceleration and jerk check boxes in ideamaker. In that case those are used. That’s my understanding.
by Noren
Sat Nov 17, 2018 5:27 pm
Forum: General
Topic: Shrinkage in Circular object
Replies: 1
Views: 191

Re: Shrinkage in Circular object

Additional cooling could help some. Also lower the distance between layer and support. And print with dense support layers.
by Noren
Mon Nov 12, 2018 6:10 pm
Forum: Hardware
Topic: what cameras work on n 2plus
Replies: 3
Views: 216

Re: what cameras work on n 2plus

Realt don’t know. Haven’t pulled images to the computer yet. And I don’t have the standard Raise3D camera to compare to.
by Noren
Mon Nov 12, 2018 3:47 pm
Forum: Hardware
Topic: what cameras work on n 2plus
Replies: 3
Views: 216

Re: what cameras work on n 2plus

On my N1 the Logitech C922 camera works.
by Noren
Mon Nov 12, 2018 3:46 pm
Forum: Software
Topic: IM Graphic Box showing up in new release
Replies: 3
Views: 180

Re: IM Graphic Box showing up in new release

Uncheck "Show extruders printing range".

Skärmavbild 2018-11-12 kl. 16.45.21.png
by Noren
Thu Oct 25, 2018 10:18 pm
Forum: Printing Settings
Topic: Poor quality top surface
Replies: 2
Views: 219

Re: Poor quality top surface

Try lowering the flow rate 10% and see if it makes a difference.
by Noren
Wed Oct 24, 2018 2:54 pm
Forum: Printing Settings
Topic: What does density affect?
Replies: 1
Views: 139

What does density affect?

What effect does changing the filament density have in the finished print? Does it affect anything more than the estimated print time? Does it affect the print?

Go to advanced search