Search found 27 matches

by jvingaard
Mon Feb 19, 2018 4:17 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 69
Views: 1237

Re: LIN_ADVANCE = better extrusion control

I have added the Raise3D Filament Monitor code to these compiled firmware versions: http://forum.raise3d.com/viewtopic.php?f=3&t=6244&p=25627#p25627 and to the BLTOUCH firmware here (not compiled): https://github.com/ABH10/Marlin-for-Raise3D-N-series/tree/1.1.x_Raise3D_BLTouch I didn't do t...
by jvingaard
Sun Feb 11, 2018 8:04 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 69
Views: 1237

Re: LIN_ADVANCE = better extrusion control

Hello ABH,
Do you have an list over g-code commands for LIN-ADVANCE w/BLTouch etc.
by jvingaard
Sun Feb 11, 2018 4:52 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 69
Views: 1237

Re: LIN_ADVANCE = better extrusion control

After removing the extra #endif and compiling it with arduino-1.6.9, all is works perfect.

Looking forward to testing it.

Many Thanks.
by jvingaard
Sun Feb 11, 2018 11:24 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 69
Views: 1237

Re: LIN_ADVANCE = better extrusion control

Hello,
When i try to compile the 1.1.x_Raise3D_BLTouch i get an 'endif without if' in the 'configuration.h'
Using Arduino 1.6.9
Board = Arduino/Genuino Mega or Mega 2560
Processor = ATmega2560 (Mega 2560)
by jvingaard
Sun Feb 11, 2018 8:30 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 69
Views: 1237

Re: LIN_ADVANCE = better extrusion control

It turns out that Raise3D is still using the M112 command for restarting the motion controller MCU, when FastStop is pressed. I put a sniffer on the serial line from the Raise Touch computer to see what happened. The problem with the Marlin 1.1.8 based firmware was in the new Marlin feature enabled...
by jvingaard
Wed Feb 07, 2018 5:31 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 69
Views: 1237

Re: LIN_ADVANCE = better extrusion control

Is there a firmware for N2Dual with BLtouch and LIN_ADVANCE
by jvingaard
Wed Jan 31, 2018 4:00 pm
Forum: Software
Topic: ideaMaker 3.1.0 Release Note
Replies: 26
Views: 793

Re: ideaMaker 3.1.0 Release Note

lorenolepi wrote:I'm a fan of the new infill and solid fill patterns. Thanks!


Yes. more of that.
by jvingaard
Fri Jan 26, 2018 6:13 am
Forum: Software
Topic: Touchscreen Firmware 0.9.7 Release Note 2018.1.16
Replies: 46
Views: 1533

Re: Touchscreen Firmware 0.9.7 Release Note 2018.1.16

Next time you release an Raise Touch update, please remove the confirmation when leaving Screen Lock, that doesn't make any sense. The confirmation is for double confirm that the unlock operation was triggered by a human on purpose, in case any touching by mistake from pets, kids. Yes, I understand...
by jvingaard
Thu Jan 25, 2018 8:44 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.7 Release Note 2018.1.16
Replies: 46
Views: 1533

Re: Touchscreen Firmware 0.9.7 Release Note 2018.1.16

Next time you release an Raise Touch update, please remove the confirmation when leaving Screen Lock, that doesn't make any sense.
by jvingaard
Tue Jan 23, 2018 9:11 pm
Forum: Hardware
Topic: LCD screen burn in
Replies: 50
Views: 4947

Re: LCD screen burn in

you write 'Screen saver has already been added in version 0.9.0 touchscreen firmware.' i don't see it anywhere.
by jvingaard
Tue Jan 23, 2018 7:22 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.7 Release Note 2018.1.16
Replies: 46
Views: 1533

Re: Touchscreen Firmware 0.9.7 Release Note 2018.1.16

After updating to the new Raise Touch, the screen is flashing after turn-off just like an photoblitz.
by jvingaard
Mon Nov 13, 2017 4:46 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 13141

Re: ideaMaker 3.0-beta Release Note Updated Rev. 3.0.3 2017.11.13

It would be nice. When you now are doing so much new things with IdeaMaker, to add VariSlice. :-)
by jvingaard
Sun Oct 29, 2017 8:47 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 13141

Re: ideaMaker 3.0-beta Release Note 2017.10.23 Updated Rev. 3.0.1 2017.10.28

Hello,
Dense Suppor Layer is not working right.
by jvingaard
Sun Oct 29, 2017 9:40 am
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 13141

Re: ideaMaker 3.0-beta Release Note 2017.10.23

Since this is a 3D accelerated application requiring proper 3D graphics support in your computer's operating system and graphics hardware driver- the most likely answer is that a driver or lack of proper accelerated graphics support in your computer is causing issues with the application. This is n...
by jvingaard
Fri Oct 27, 2017 5:46 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 13141

Re: ideaMaker 3.0-beta Release Note 2017.10.23

Hello, Preview window is not showing any options, only a blank window frame. Since this is a 3D accelerated application requiring proper 3D graphics support in your computer's operating system and graphics hardware driver- the most likely answer is that a driver or lack of proper accelerated graphi...
by jvingaard
Thu Oct 26, 2017 5:04 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 13141

Re: ideaMaker 3.0-beta Release Note 2017.10.23

Hello,
Preview window is not showing any options, only a blank window frame.
by jvingaard
Wed Aug 30, 2017 4:37 pm
Forum: Feature requests, ideas, wishes
Topic: Filament Monitor / Auto Pause Feature
Replies: 10
Views: 1950

Re: Filament Monitor / Auto Pause Feature

Vicky@Raise3D wrote:We will developing a filament monitor currently. Not only detect out of filament but also nozzle clogging.


When are you planning to release the filament monitor
by jvingaard
Mon Jan 16, 2017 9:15 am
Forum: Feature requests, ideas, wishes
Topic: IdeaMaker mac fixes.
Replies: 15
Views: 1213

Re: IdeaMaker mac fixes.

I can confirm that!
by jvingaard
Mon Jan 16, 2017 3:58 am
Forum: Feature requests, ideas, wishes
Topic: ideamaker windows size
Replies: 1
Views: 399

ideamaker windows size

The ability for ideamaker to keep the windows size after exit. (min/max/customize)
by jvingaard
Sun Jan 15, 2017 12:20 pm
Forum: Feature requests, ideas, wishes
Topic: Slice Preview
Replies: 2
Views: 543

Slice Preview

Adding Feature Type til slice preview.

Go to advanced search