Search found 33 matches

by ssommer79
Wed Dec 27, 2017 10:11 pm
Forum: Software
Topic: Flowrate
Replies: 1
Views: 205

Flowrate

Hello I defined two settings: Start Z 0.00 till 0.60 with a Flowrate of 92% Start Z 0.60 till 0.00 (end) with a Flowrate of 100% How can i check in the gcode, if these values are really existing? I only found two M221 commands M221 T0 S100.00 (Start Script) ;M221 T0 S100.00 (bottom of the GCODE) Zwi...
by ssommer79
Fri Nov 24, 2017 12:16 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Re: ideaMaker 3.0-beta Release Note Updated Rev. 3.0.3 2017.11.13

For the fan speed, we have tried the same fan settings, and didn't see any fan stop code after layer 1. May I ask your gcode to have a look? Attached our gcode for you to test also. 20mm_Calibration_Box.rar Pleas see attached files. On Line 35 you can see that the Fan Speed will be set to Maximum (...
by ssommer79
Fri Nov 24, 2017 9:38 am
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Re: ideaMaker 3.0-beta Release Note Updated Rev. 3.0.3 2017.11.13

Hi For the temperature control list, I'm so sorry that confuses you, but if we leave waiting or pause code there, the nozzle will ooze a lot. We will more recommend you to set the temperature change point in advance, maybe 2 or 3 layers to make the nozzle completely reach the value before getting t...
by ssommer79
Fri Nov 24, 2017 9:36 am
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Dense Support at manual Support

-------------- EDIT: This bug was already fixed within newest version -------------- Maybe i do not understood, but if i choose that dense support should be placed, this should be done also when i add the support manually, or? My support settings: support_auto1.jpg When i choose to automatically pla...
by ssommer79
Thu Nov 23, 2017 7:50 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Re: ideaMaker 3.0-beta Release Note Updated Rev. 3.0.3 2017.11.13

Hi If i used the Temperature Control List. I configured like on this screenshot: Zwischenablage02.jpg It heats up before printing to 240 and only when he starts printing (during printing) the first layer heats up higher till 250. When i choose a first layer temperature from 250 degrees, i expect tha...
by ssommer79
Thu Oct 26, 2017 10:11 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Re: ideaMaker 3.0-beta Release Note 2017.10.23

Very nice! Will give it a try I like the kind of way, Simplify heat up. First the bed will go up to the temperature choosen and only if heatbed is on 100% the Extruder will heat up. Normally the Extruder warm up much faster. In the old version of Ideamaker the extruder went up first - and the the h...
by ssommer79
Thu Oct 26, 2017 10:08 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Re: ideaMaker 3.0-beta Release Note 2017.10.23

Vicky@Raise3D wrote:
ssommer79 wrote:If i choose 5 Lines BRIM, why the Brim will not fit the outer border of the model on the whole model? You can see some strange behaviour generating the BRIM


Is it possible that we can ask the .STL file of this model for testing?


Hello Vicky

Of course. Please see attached file

Regards, Sascha
by ssommer79
Wed Oct 25, 2017 8:05 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Re: ideaMaker 3.0-beta Release Note 2017.10.23

If i choose 5 Lines BRIM, why the Brim will not fit the outer border of the model on the whole model? You can see some strange behaviour generating the BRIM
by ssommer79
Wed Oct 25, 2017 8:01 pm
Forum: Software
Topic: ideaMaker 3.0-RC Release Note Updated Rev. 3.0.5 2017.12.18
Replies: 263
Views: 20014

Re: ideaMaker 3.0-beta Release Note 2017.10.23

Very nice! Will give it a try I like the kind of way, Simplify heat up. First the bed will go up to the temperature choosen and only if heatbed is on 100% the Extruder will heat up. Normally the Extruder warm up much faster. In the old version of Ideamaker the extruder went up first - and the the he...
by ssommer79
Tue Jun 13, 2017 7:05 am
Forum: Hardware
Topic: Where to get new rods
Replies: 5
Views: 792

Re: Where to get new rods

I've struggled also with the same Problem (http://forum.raise3d.com/viewtopic.php?f=4&t=1089). I've changed all rods. It became better but not solved the Problem. the bed is still not flat (+/- 0.5mm). I am still fighting with Problems. Fortunetaly my seller here in Switzerland is very responsiv...
by ssommer79
Mon Apr 24, 2017 9:03 am
Forum: Hardware
Topic: Bed leveling again
Replies: 6
Views: 1213

Re: Bed leveling again

I had (and have) the same Problem, which i reported also here (http://forum.raise3d.com/viewtopic.php?f=4&t=1089&p=9995#p11107). In my case the rods where not straight. After changing them, it was better. But quite a part away from "perfect". If you have that problem, you will not ...
by ssommer79
Fri Apr 07, 2017 2:48 pm
Forum: Hardware
Topic: Olsson Ruby, will it fit?
Replies: 26
Views: 4102

Re: Olsson Ruby, will it fit?

Just for my understanding the whole thing:

On your picture, there's a gap between the heater block and the nozzle. Does this not make a problem with the temperature at the nozzle top / where the filament will be pulled out?

Unbenannt-1.jpg
by ssommer79
Mon Apr 03, 2017 11:19 am
Forum: Hardware
Topic: Olsson Ruby, will it fit?
Replies: 26
Views: 4102

Re: Olsson Ruby, will it fit?

Means, if i buy this Version "Olsson Ruby Düse - E3D V5/V6 - 1.75mm / 0.4mm" this will fit my V2 Hotend?
by ssommer79
Mon Apr 03, 2017 11:12 am
Forum: Hardware
Topic: Project: The next heated bed
Replies: 30
Views: 4386

Re: Project: The next heated bed

If i would like to change the current heated bed on my N2 to another 24V Versions, what is the Limit for the "Watt"?

24V/200W, 24V/300W, 24V/400W, 24V/480W?
by ssommer79
Fri Mar 24, 2017 9:11 am
Forum: Hardware
Topic: BlTouch / Printer do not start / boot anymore
Replies: 3
Views: 617

Re: BlTouch / Printer do not start / boot anymore

For some readers who are reading here / find this thread with the same problem: I am dealing currently with the raise3d support about this problem. Engaged and helpful support! I have no idea HOW this could happen - maybe just bad luck or a "monday-model". Often already a Hard Reset fix th...
by ssommer79
Wed Mar 22, 2017 8:21 pm
Forum: Hardware
Topic: BlTouch / Printer do not start / boot anymore
Replies: 3
Views: 617

Re: BlTouch / Printer do not start / boot anymore

Noticed now, than with plugged in battery the Display does not shutdown now (the backlights stays on). Only with unplugged battery the display becomes 100% off.
by ssommer79
Wed Mar 22, 2017 8:00 pm
Forum: Hardware
Topic: BlTouch / Printer do not start / boot anymore
Replies: 3
Views: 617

Re: BlTouch / Printer do not start / boot anymore

In the past i already have 2 times the problem, that the Touchscreen hang up (after powering off the printer, the raise3d menu still left on the touchscreen). In this case i had to unplug the battery and replug it. The only strange thing i noticed yesterday (when it still worked), was, that when i i...
by ssommer79
Wed Mar 22, 2017 6:31 pm
Forum: Hardware
Topic: BlTouch / Printer do not start / boot anymore
Replies: 3
Views: 617

BlTouch / Printer do not start / boot anymore

Hello Till yesterday i printed more or less without problem. I always switch off the printer with the switch button at the back of the printer. Today i started again, but the printer do not boot anymore. The display stays black. No idea why! The fans and the LED lights inside are working I tried to ...
by ssommer79
Thu Feb 09, 2017 1:24 pm
Forum: Software
Topic: Model out of range
Replies: 9
Views: 1537

Re: Model out of range

it'll only let you place the model within the grid, the top left corner is hanging off, you may need to fiddle with the placement I think also the bounding frame is the Problem. But this seems to me a bug, because Simplify slice that whithout Problem - what make sense because the model itself is on...
by ssommer79
Thu Feb 09, 2017 1:22 pm
Forum: Software
Topic: Model out of range
Replies: 9
Views: 1537

Re: Model out of range

I use the current Version installed 2 weeks ago. I assume that it for Ideamaker it is a Problem, that the Rectangular bounding Frame is out of the plate. But the model itself is on the plate

Go to advanced search