Search found 177 matches

by Casale8
Sun May 20, 2018 4:51 pm
Forum: Hardware
Topic: Gear Slip at Overlapping Solidfill layer print
Replies: 7
Views: 125

Re: Gear Slip at Overlapping Solidfill layer print

I can't share the stl... as the whole is supposed to interface with a controlled assembly. It is specifically ANY SOLID LAYER that this issue is shown. And Heat Creep is a major factor... to the gear - even though I have mitigated all the way up to not changing to bondtech... I have 5 days to print ...
by Casale8
Fri May 18, 2018 7:15 pm
Forum: Feature requests, ideas, wishes
Topic: Raise3D Fan Duct Pro2 Plus
Replies: 22
Views: 946

Re: Raise3D Fan Duct Pro2 Plus

Casale8 wrote:
Vicky@Raise3D wrote:As Billucas said, yes, on the new Pro2 series, the two fans at left and right can be controlled by gcode. Only the center fan for nozzle cooling is constant-on.

Will the front fan duct for the pro2 work with the N2 dual?
by Casale8
Fri May 18, 2018 7:12 pm
Forum: Feature requests, ideas, wishes
Topic: Raise3D Fan Duct Pro2 Plus
Replies: 22
Views: 946

Re: Raise3D Fan Duct Pro2 Plus

Vicky@Raise3D wrote:As Billucas said, yes, on the new Pro2 series, the two fans at left and right can be controlled by gcode. Only the center fan for nozzle cooling is constant-on.

Will the fan duct for the pro2 work with the N2 dual?
by Casale8
Fri May 18, 2018 7:11 pm
Forum: User's Gallery
Topic: Pro-2 Front Mount Fan model
Replies: 3
Views: 100

Re: Pro-2 Front Mount Fan model

Alex M. wrote:It was already posted here. viewtopic.php?f=6&t=7111#p28725
Not sure if it's a direct fit.


Thanks.

Perhaps the holes on the front are the same? May be someone who has one can measure?
by Casale8
Fri May 18, 2018 6:15 pm
Forum: Hardware
Topic: PLA – Raft Sticking to Print
Replies: 9
Views: 631

Re: PLA – Raft Sticking to Print

I love printing with a raft. Never a problem with bed adhesion. Easy to remove from bed without damaging the actual print. I agree. However I know this is not ideal for time , or the "standard" of 3D printing. I get a fine looking layer. Only occasionally do I have issues with RAFT not co...
by Casale8
Fri May 18, 2018 6:10 pm
Forum: Hardware
Topic: Unloading PLA from BondTech extruder
Replies: 4
Views: 121

Re: Unloading PLA from BondTech extruder

I've only used the load button a few times, I just use unload and preload. I've never had a problem unloading and preloading any filament.
Always at 215°C.
by Casale8
Fri May 18, 2018 5:49 pm
Forum: Hardware
Topic: Gear Slip at Overlapping Solidfill layer print
Replies: 7
Views: 125

Re: Gear Slip at Overlapping Solidfill layer print

Interesting observation: I am able to rectify the air printing caused by the overlapping of the filament being laid out by the extruder. What I am observing with the print function itself is that the settings are creating one additional pass for the filament to fill, when there is no room for it to ...
by Casale8
Fri May 18, 2018 2:45 pm
Forum: User's Gallery
Topic: Pro-2 Front Mount Fan model
Replies: 3
Views: 100

Pro-2 Front Mount Fan model

I'm interested to see if the front mount fan for the Pro-2 will work for the N2 Dual. If so, is there an STL for the Pro-2 Front mount? I'm interested in a front mounting without wrapping it completely around the extruder (as the other available designs all seem to do) so I can added a constant on f...
by Casale8
Fri May 18, 2018 2:34 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.9 Release Note 2018.5.17
Replies: 31
Views: 334

Re: Touchscreen Firmware 0.9.9 Release Note 2018.5.17

Noticed when I STOP a print, it doesn't move the bed bad to 0, but rather some other height quite a distance from 0. Not that it's a huge concern, but it started with the update today... And could get annoying if pressed for time. Do you mean that after print stops, the bed just stop at the stopped...
by Casale8
Thu May 17, 2018 8:11 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.9 Release Note 2018.5.17
Replies: 31
Views: 334

Re: Touchscreen Firmware 0.9.9 Release Note 2018.5.17

Casale8 wrote:Noticed when I STOP a print, it doesn't move the bed back to 0, but rather some other height quite a distance from 0. Not that it's a huge concern, but it started with the update today...

And could get annoying if pressed for time.
by Casale8
Thu May 17, 2018 8:06 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.9 Release Note 2018.5.17
Replies: 31
Views: 334

Re: Touchscreen Firmware 0.9.9 Release Note 2018.5.17

Noticed when I STOP a print, it doesn't move the bed bad to 0, but rather some other height quite a distance from 0. Not that it's a huge concern, but it started with the update today...

And could get annoying if pressed for time.
by Casale8
Thu May 17, 2018 5:22 pm
Forum: Hardware
Topic: Gear Slip at Overlapping Solidfill layer print
Replies: 7
Views: 125

Re: Gear Slip at Overlapping Solidfill layer print

I know you and I previously discussed and I'm 99.9% sure you are at least running the sharp tooth drive gear I linked and recommended. That's a good upgrade and does improve grip, but alone it does not solve all the known potential shortcomings of the stock extruder feeder system. Jetguy, to your k...
by Casale8
Thu May 17, 2018 3:07 pm
Forum: Hardware
Topic: Gear Slip at Overlapping Solidfill layer print
Replies: 7
Views: 125

Re: Gear Slip at Overlapping Solidfill layer print

JetGuy,

Your input is invaluable - thank you.
by Casale8
Thu May 17, 2018 12:43 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.9 Release Note 2018.5.17
Replies: 31
Views: 334

Re: Touchscreen Firmware 0.9.9 Release Note 2018.5.17

Vicky@Raise3D wrote:Hi All,

[/b]Added new features and options
Fixed bugs based on users' feedback


Curiously, could we be more specific?
by Casale8
Wed May 16, 2018 8:39 pm
Forum: Printing Settings
Topic: First layer = Crap?
Replies: 8
Views: 154

Re: First layer = Crap?

Don't use raft for a part you want the face to be perfect on. Jet Guy, I specifically use raft to get better quality prints on the base because I need a guaranteed adhesion to the bed - and I use glue. I'm eight months new to 3D printing though... I get really nice quality prints with raft. I am cu...
by Casale8
Wed May 16, 2018 5:33 pm
Forum: Hardware
Topic: Gear Slip at Overlapping Solidfill layer print
Replies: 7
Views: 125

Gear Slip at Overlapping Solidfill layer print

Any thoughts are appreciated in advance. I hope I described it enough to be understood. ESD-ABS 240°C (dropped to 225°C). Bed 110°C blah blah blah. I've been printing various materials very successfully since I received the printer. A little trial and error and I get better than expected prints (th...
by Casale8
Mon May 07, 2018 7:57 pm
Forum: Printing Settings
Topic: ABS warping
Replies: 33
Views: 1463

Re: ABS warping

EldRick wrote:
That's assumed necessary as soon as you take the glass with the buildtak and replace it with the glass without.


You don't need to replace or re-level anything and probably won't even need to adjust the print height - just flip the buildplate over and print on the glass side.

INTERESTING
by Casale8
Fri May 04, 2018 4:48 pm
Forum: Printing Settings
Topic: ABS warping
Replies: 33
Views: 1463

Re: ABS warping

Reluctantly, I guess I will have to try printing ABS on the glass after all (for large prints). ;P So I've done some testing with WolfBite on glass. 2 hours of testing at 240 nozzle and 100 bed. Fun stuff :roll: - small 1.25 x 1.25 print didn't even make it to the end of the first layer before it w...
by Casale8
Fri May 04, 2018 3:53 pm
Forum: Printing Settings
Topic: ABS warping
Replies: 33
Views: 1463

Re: ABS warping

I never got anywhere with ABS until I started using "ABS Juice" on the glass bed. I use SimpleGreen to clean off the surface of the glass and wipe it till it squeaks. Then generously slather acetone/ABS slurry over the bed, pre-heat it for about 10-15 minutes and get printing. When the pr...

Go to advanced search