Search found 102 matches

by sylus
Wed Aug 08, 2018 10:12 am
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 93
Views: 6552

Re: LIN_ADVANCE = better extrusion control

@ABH ,last Marlin 1.1x is out.Did you plan to update your firmware?Have you experienced printer stop in mid print recently with 1.1.8 and last Raisetouch firmware?
by sylus
Mon Jul 30, 2018 9:13 pm
Forum: Hardware
Topic: Replacement Board, Serial Error: No Such Device or Adress
Replies: 6
Views: 175

Re: Replacement Board, Serial Error: No Such Device or Adress

you have to reflash firmware from arduino IDE
by sylus
Thu Apr 26, 2018 7:08 pm
Forum: Hardware
Topic: Palette+ and N2 Set up
Replies: 13
Views: 899

Re: Palette+ and N2 Set up

with this setup had no problems
https://www.thingiverse.com/thing:2829055
by sylus
Thu Mar 01, 2018 3:04 pm
Forum: Hardware
Topic: Motion controller blower noise reduction by Vernon Barry
Replies: 12
Views: 3928

Re: Motion controller blower noise reduction by Vernon Barry

why not use 5 V pinout directly from the Rumba? Because a brushless fan motor generates some EMI/RFI noise and draws a fair amount of power. The regulator onboard for 5V was intended only to power the logic circuits and not fans and other loads. Rather than risk problems, glitches, and maybe even f...
by sylus
Tue Feb 27, 2018 11:56 am
Forum: Hardware
Topic: Motion controller blower noise reduction by Vernon Barry
Replies: 12
Views: 3928

Re: Motion controller blower noise reduction by Vernon Barry

why not use 5 V pinout directly from the Rumba?
by sylus
Mon Feb 26, 2018 11:20 am
Forum: General
Topic: "M900 K30" G script
Replies: 2
Views: 270

Re: "M900 K30" G script

no linear advance with official firmware.
works with 1.1.8 from ABH or firesped
by sylus
Thu Feb 22, 2018 1:02 pm
Forum: General
Topic: Update FW... HOW?
Replies: 17
Views: 2117

Re: Update FW... HOW?

Haven't tried checking fuse bits with the connectors you mentioned. We use JTAG to flash firmware and boothloader and SPI as the communication Bus. Interrested to have the procedure by MP because I have a new spare controller from my supplyer wich is not detected via usb. It's seems bootloder is no...
by sylus
Thu Feb 22, 2018 12:46 pm
Forum: General
Topic: Thermal-Protector - available soon to all
Replies: 108
Views: 25398

Re: Thermal-Protector - available soon to all

Wise decision and ethical decision.
by sylus
Mon Feb 12, 2018 6:55 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 93
Views: 6552

Re: LIN_ADVANCE = better extrusion control

Lin addvance @50 for bondtech. Strange behavior with Marlin 1.1.8 jog with PC duino is buggy 10 mm increment is ok in all direction 1 mm increment goes only in one direction (+X+Y) and 0,1 mm increment goes only in one direction (+X+Y) and not jog 0,1mm Z axis is not affected Jogging Rumba via Repra...
by sylus
Sun Feb 11, 2018 7:29 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 93
Views: 6552

Re: LIN_ADVANCE = better extrusion control

Ok fast stop is not so fast (some commands sent before M112).
Still implementing lack of material code
by sylus
Sun Feb 11, 2018 6:00 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 93
Views: 6552

Re: LIN_ADVANCE = better extrusion control

seen in changing tool script
M42 P8 S255
by sylus
Sun Feb 11, 2018 3:58 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 93
Views: 6552

Re: LIN_ADVANCE = better extrusion control

Are you serious?
B6FE346F-CA7A-477C-AADD-03915F94DE35.jpeg
by sylus
Tue Jan 23, 2018 11:48 am
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 83
Views: 4749

Re: Filament Run-out Sensor Add-on

My main complaint here is the thermal protection should be a free or near free separate add on. There should be instructions and open source for mass producing it, it's 2 resistors and the connection cables, basically the identical copy of the hardware mod just plug into the mainboard. Don't get me...
by sylus
Fri Jan 19, 2018 6:55 am
Forum: Hardware
Topic: Adjusting E-steps for the old Bondtech extruder
Replies: 5
Views: 518

Re: Adjusting E-steps for the old Bondtech extruder

Apologies if this has been answered already. I am using the older Bondtech extruder (1 x direct drive, 1 x bowden), and I just noticed that Bondtech have updated their instructions to adjust the E-step value. With the new firmware, it's now done directly through the settings menu on the machine: ht...
by sylus
Sat Jan 13, 2018 10:53 pm
Forum: Hardware
Topic: Raise3D-printers compatible with Astroprint?
Replies: 6
Views: 1374

Re: Raise3D-printers compatible with Astroprint?

Yes it works,as octoprint too but with the sacrifice of the raisetouch.
by sylus
Thu Jan 11, 2018 9:08 pm
Forum: Printing Settings
Topic: Z offset
Replies: 18
Views: 1169

Re: Z offset

To avoid this issue ,I recommand to Raise3D to allow babytepping from the Pcduino and store it as Estep and other parametrable setting. then setting with endstop screw was done only one time. When we change noozle we can set the correct height dynamically and finally store the Z offset. It could be ...
by sylus
Tue Jan 02, 2018 10:10 pm
Forum: Hardware
Topic: E3D v6 Adaptor
Replies: 150
Views: 11425

Re: E3D v6 Adaptor

M42 P8 Sxxx (0-255)
by sylus
Fri Dec 29, 2017 3:08 pm
Forum: Hardware
Topic: Printer Filament Monitor
Replies: 76
Views: 10089

Re: Printer Filament Monitor

another load on the print head.....where is the clogging detection?The chosen technology (optical sensor) will not allow to monitor that.
good news for bondetech user custom solution exist and works well (mechanical endstop or optical).
by sylus
Thu Dec 21, 2017 9:47 pm
Forum: Hardware
Topic: How are your stepper motors wired?
Replies: 1
Views: 208

Re: How are your stepper motors wired?

I confirm,on my unit all coil are well connected as it should be
by sylus
Sun Dec 17, 2017 8:02 pm
Forum: Hardware
Topic: Bltouch on Raise3d
Replies: 133
Views: 18219

Re: Bltouch on Raise3d

As the motherboard installed Z min pin is down and ground up

Go to advanced search