Search found 188 matches

by Billucas
Sat May 19, 2018 2:43 am
Forum: Feature requests, ideas, wishes
Topic: Raise3D Fan Duct Pro2 Plus
Replies: 22
Views: 1129

Re: Raise3D Fan Duct Pro2 Plus

I don't think so. This is why I whant to draw another that fit the N2 dual. When I will have time.
by Billucas
Fri May 18, 2018 11:42 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.10 Release Note 2018.6.5
Replies: 82
Views: 2035

Re: Touchscreen Firmware 0.9.9 Release Note 2018.5.17

Casale8 wrote:No ma'am. The Bed does not stop at the stopped height, the bed moves down to about the middle of the available Z. Almost as if it were intended to offer our hands more room to remove the model from the bed.

I have the same observation. It is 4 inches lower than before the last update.
by Billucas
Thu May 17, 2018 5:34 pm
Forum: Hardware
Topic: Printer unable to connect over Wifi
Replies: 6
Views: 146

Re: Printer unable to connect over Wifi

pearson222 wrote:It will not connect to any wireless network.


Same for me. No WI-FI since two firmwares updates... And no solution.
by Billucas
Thu May 17, 2018 1:53 pm
Forum: General
Topic: Thermal-Protector - available soon to all
Replies: 96
Views: 20899

Re: Thermal-Protector - available soon to all

tulsah wrote:Has anyone in Canada received there's yet?


Mine is in Montreal at the custom border at Dorval since a week!
by Billucas
Tue May 08, 2018 12:25 pm
Forum: Hardware
Topic: no networking all of a sudden
Replies: 24
Views: 1254

Re: no networking all of a sudden

For me, it is since the "updater_0_9_7_1509.raisepack".

Thanks
by Billucas
Tue May 08, 2018 1:42 am
Forum: Hardware
Topic: no networking all of a sudden
Replies: 24
Views: 1254

Re: no networking all of a sudden

Alex M. wrote: Did anyone else's issues start after upgrading the Touchscreen firmware?

Yes I have the same problem after an update see topic viewtopic.php?f=3&t=5957#p25268
I wrote To Raise support, but it does not tell me. So I don't have wifi for now.
by Billucas
Fri Apr 20, 2018 4:23 pm
Forum: General
Topic: Just Released N2 Pro
Replies: 125
Views: 26232

Re: Just Released N2 Pro

The use of 3D printed parts in new products is becoming more and more common. If there is 3d printed parts made by Raise3d, I hope they will put more quality on the material used and a better external finish. Because I have seen ugly parts sometime in the past. And if we look on the pictures of the...
by Billucas
Tue Apr 17, 2018 3:44 pm
Forum: General
Topic: Looking for a printer, should we buy a new Pro2, new N2 or a used N2?
Replies: 7
Views: 2029

Re: Looking for a printer, should we buy a new Pro2, new N2 or a used N2?

It really all depends on WHAT you plan to use the machine for. Are you a prototyping shop? Are you an enthusiast? Do you need to print with any filament or will PLA work? A lot of questions to better help us. The closed firmware hasn't been an issue for us. Do you really intend on making any change...
by Billucas
Mon Apr 16, 2018 4:54 pm
Forum: Feature requests, ideas, wishes
Topic: Really perfect self repair instructions ...
Replies: 5
Views: 384

Re: Really perfect self repair instructions ...

Sorry if I have to mention this time the competition, but since I myself was a customer of Zortrax I have to mention the MODEL support page of Zortrax ... SO must be a support page for your own hardware / software that truly explains StepbyStep's instructions for repair and / or problems. RAISE3D i...
by Billucas
Thu Apr 12, 2018 12:52 pm
Forum: General
Topic: ABS Build Surface - PEI? Geckotek?
Replies: 19
Views: 3169

Re: ABS Build Surface - PEI? Geckotek?

Here some images of some big prints I made with the LokBuild bed surface. To encourage you! In the past, I have tested to put a 1/8" thick aluminium plate instead of a glass. Finally this was not flat or straight enough. I bought 2 High Temperature Build Plate from Raise3d, in order to have man...
by Billucas
Thu Apr 12, 2018 12:40 pm
Forum: Hardware
Topic: Bondtech BMG upgrade for the N series
Replies: 212
Views: 24889

Re: Bondtech BMG upgrade for the N series

Yesterday, my friend came to my house yesterday with his Multimeter. We lowered the voltage of the stepper motor of the Bondtech extruders at 0.5V. So, everything is set now! I did not have clogging issue. I tried with ABS, with the Top cover on, for a 20 hours print. No problem. Just to let you kno...
by Billucas
Wed Apr 11, 2018 8:15 pm
Forum: Hardware
Topic: TOP COVER Replacement N2+N2 Plus
Replies: 14
Views: 876

Re: TOP COVER Replacement N2+N2 Plus

Here a image of the future assembly.
by Billucas
Wed Apr 11, 2018 8:12 pm
Forum: Feature requests, ideas, wishes
Topic: N2 Cover
Replies: 21
Views: 3114

Re: N2 Cover

Here a image of the future assembly.
by Billucas
Wed Apr 11, 2018 7:23 pm
Forum: Feature requests, ideas, wishes
Topic: Raise3D Fan Duct Pro2 Plus
Replies: 22
Views: 1129

Re: Raise3D Fan Duct Pro2 Plus

On the “old” printers the left and right fans are always on. And the extra fan connection can be controlled via gcode. But the new printers I don’t know. I know. But you could put the left and right fans be controlled via gcode ( controller board there is 2 empty plugs) , and add a central 40mm fan...
by Billucas
Wed Apr 11, 2018 6:45 pm
Forum: Feature requests, ideas, wishes
Topic: Raise3D Fan Duct Pro2 Plus
Replies: 22
Views: 1129

Re: Raise3D Fan Duct Pro2 Plus

Noren wrote:With this new design how do you go about printing abs? No lid for the fan duct?


I think that the central fan is only for hot ends. The left and right side fans are control by Ideamaker.
Am I right?
by Billucas
Wed Apr 11, 2018 3:59 pm
Forum: Feature requests, ideas, wishes
Topic: Raise3D Fan Duct Pro2 Plus
Replies: 22
Views: 1129

Re: Raise3D Fan Duct Pro2 Plus

Thank you Vicky, I appreciate. So, like we thought, there is some changes between the N2-N2-Plus and the Pro2.
It will give me an idea how to mix the Fan Duct design, in order to retrofit our cooling system. I know that many people
have done this, but I will give a look.

Luc
by Billucas
Wed Apr 11, 2018 12:48 am
Forum: Hardware
Topic: Printer Filament Monitor
Replies: 76
Views: 9553

Re: Printer Filament Monitor

Has this thing shipped yet? I'm pretty sure I pre-ordered as soon as I got the email. If not, any new release date? Last estimate from Raise was "March", which I'm pretty sure is over. I second. I order it the day 1, and I did not received it yet. And I hope it will be an injection molded...
by Billucas
Tue Apr 10, 2018 7:55 pm
Forum: General
Topic: ABS Build Surface - PEI? Geckotek?
Replies: 19
Views: 3169

Re: ABS Build Surface - PEI? Geckotek?

So I have a Lokbuild surface and a spool of eSun ABS+ arriving tomorrow for Amazon. :) I will let you all know how it shakes out. Great! Take care not to clean your LokBuild with Isopropyl Alcohol more than 30% ( not 70%), as the supplier says. Also, be careful for the z height between the surface ...
by Billucas
Tue Apr 10, 2018 4:19 pm
Forum: Hardware
Topic: Bondtech BMG upgrade for the N series
Replies: 212
Views: 24889

Re: Bondtech BMG upgrade for the N series

I never remove the top cover unless printing PLA. I haven't done 50 hours with ABS, but I've done some 30 hour prints without issue. 40+ hours on PETG. Ok good. I wonder what is the temperature of your stepper motors from the extruders? Of course, during your long prints and with the top cover. Luc
by Billucas
Tue Apr 10, 2018 2:26 pm
Forum: General
Topic: ABS Build Surface - PEI? Geckotek?
Replies: 19
Views: 3169

Re: ABS Build Surface - PEI? Geckotek?

So, those two build surfaces that you are recommending. Are they specifically the best that you've found for ABS or just the best all-around? I've found that most surface materials that are great for some plastics don't play as well with others. They are also The best for ABS. http://www.lokbuild.c...

Go to advanced search