Search found 89 matches

by woofy
Wed Aug 02, 2017 3:19 pm
Forum: Hardware
Topic: BMG Bondtech extruder: important
Replies: 23
Views: 384

Re: BMG Bondtech extruder: important

Exactly the problem I had here:
viewtopic.php?f=5&t=1470#p15549

The cable partially came out and the hotend went into overdrive.
This connector must be anchored down.
by woofy
Wed Jul 26, 2017 8:52 am
Forum: Others
Topic: I hate site localization and redirecting!
Replies: 7
Views: 159

Re: I hate site localization and redirecting!

Yes, it works ok.
by woofy
Thu Jul 20, 2017 4:34 pm
Forum: Others
Topic: I hate site localization and redirecting!
Replies: 7
Views: 159

Re: I hate site localization and redirecting!

Vicky, Here is an example of where it is annoying. In this post Jetguy is referencing a lot of pages, and I'm sure the links work just fine for him. http://forum.raise3d.com/viewtopic.php?p=16819#p16809 But for us in Europe we are just redirected to the EU home page. If you could change your redirec...
by woofy
Thu Jul 20, 2017 3:16 pm
Forum: User's Gallery
Topic: Single extruder multiple color using the Mosaic Palette
Replies: 79
Views: 3767

Re: Single extruder multiple color using the Mosaic Palette

Oh that's very clever, I like that kind of lateral thinking.
Thanks for the explanation.
by woofy
Thu Jul 20, 2017 11:41 am
Forum: User's Gallery
Topic: Single extruder multiple color using the Mosaic Palette
Replies: 79
Views: 3767

Re: Single extruder multiple color using the Mosaic Palette

Yes, the system has feedback and attempts corrections. But again, there are limits here. Filament is cut and spliced to commanded lengths per the gcode. When you printer makes one tiny difference in actual VS commanded, that cascades and shifts everything. If that shift is greater than the buffer o...
by woofy
Mon Jul 17, 2017 9:39 am
Forum: General
Topic: SPAM Bots again
Replies: 10
Views: 542

Re: SPAM Bots again

You're doing all the right things now. If the spammers see they are not getting through it will slow down considerably. You will always need to keep an eye on the new posts you moderate. Tricks they use include silly responses such as suggesting resetting the phone in the one above. Another common t...
by woofy
Fri Jul 14, 2017 12:34 pm
Forum: General
Topic: SPAM Bots again
Replies: 10
Views: 542

Re: SPAM Bots again

It still needs vigilance.
Here is a spammer (mariareese) using an age old trick to get passed moderation:
viewtopic.php?f=2&t=1274#p16500
by woofy
Mon Jul 10, 2017 11:57 am
Forum: Hardware
Topic: Is there a UK ideally London Service Centre as really had it with the problems Im having
Replies: 1
Views: 96

Re: Is there a UK ideally London Service Centre as really had it with the problems Im having

iMakr are in London and are Raise3D distributors.
They may be able to help, at least its worth a phone call.
by woofy
Fri Jul 07, 2017 11:49 am
Forum: Hardware
Topic: Suck or blow?
Replies: 2
Views: 93

Re: Suck or blow?

blow
by woofy
Mon Jul 03, 2017 8:24 am
Forum: User's Gallery
Topic: Fantasy Castle
Replies: 7
Views: 347

Re: Fantasy Castle

Amazing!

I would be concerned about the nozzle clouting those towers. Did you use a z-hop?
by woofy
Fri Jun 30, 2017 12:41 pm
Forum: General
Topic: SPAM Bots again
Replies: 10
Views: 542

Re: SPAM Bots again

If we get SPAM report, we will delete the thread and block that account. That's really not good enough, Vicky. Leave it at that and you will be swamped with spam. The folks here will quickly get as fed up with reporting it as you will with deleting it. I used to run a forum and the only way to stop...
by woofy
Fri Jun 30, 2017 9:35 am
Forum: User's Gallery
Topic: Baby Groot
Replies: 2
Views: 198

Baby Groot

3 1/2 days printing, I have my full size baby groot.

groot1.jpg


groot2.jpg


groot3.jpg
by woofy
Wed Jun 21, 2017 4:43 pm
Forum: User's Gallery
Topic: Wall of shame prints (print failures)
Replies: 18
Views: 1578

Re: Wall of shame prints (print failures)

That possibly caused the xy shift. I haven't insulated the block and I forgot to put a z-hop on. But the fans stopping and run away over heating? Despite being separate circuits, they had a common cause. I'd recently installed the Bondtech extruder, and when I re-assembled the head I had too much te...
by woofy
Wed Jun 21, 2017 12:48 pm
Forum: User's Gallery
Topic: Wall of shame prints (print failures)
Replies: 18
Views: 1578

Re: Wall of shame prints (print failures)

Had this Baby Groot fail about 55 hours into a 65hr print. Sob! It started with an xy skip. After a while of spewing filament into thin air, the fans stopped and the thermocouple failed. The heater went mad and started smoking. The printed fan cover melted and filament jammed in the throat tube, eve...
by woofy
Wed Jun 07, 2017 4:24 pm
Forum: User's Gallery
Topic: 35mm PCB Posts
Replies: 1
Views: 211

35mm PCB Posts

A simple but effective way to keep prototype PCB's off the bench.

20170607_165103.jpg


20170607_165906.jpg
by woofy
Tue Jun 06, 2017 7:50 am
Forum: User's Gallery
Topic: Medusa chandelier
Replies: 20
Views: 1878

Re: Medusa chandelier

Stratosphere wrote:Love this!

Thanks.
Let us know if you make one.
by woofy
Thu Jun 01, 2017 9:01 am
Forum: Hardware
Topic: Bondtech BMG upgrade for the N series
Replies: 171
Views: 5415

Re: Bondtech BMG upgrade for the N series

Modifying a probe to also adjust the pot - that's a good idea. I've just set stock drivers to the recommended 0.5v the hard way, small adjustments and recheck. It's slow but I'll likely not be doing it much.
by woofy
Wed May 31, 2017 1:29 pm
Forum: Hardware
Topic: Bondtech BMG upgrade for the N series
Replies: 171
Views: 5415

Re: Bondtech BMG upgrade for the N series

I fitted my BMG upgrade this morning, excellent instructions an very easy to do. I'm doing a test print now, but its looking good so far. I had the black motors on my N2+ extruder. On the BMG I had to swap the motor wires on the rear motor (right extruder) only. The front motor (left extruder) remai...
by woofy
Thu May 25, 2017 9:46 pm
Forum: Hardware
Topic: Bondtech BMG upgrade for the N series
Replies: 171
Views: 5415

Re: Bondtech BMG upgrade for the N series

Not sure if anyone's got them yet.
I ordered on Monday but have not even had an acknowledgement so far.
by woofy
Mon May 22, 2017 9:54 am
Forum: Hardware
Topic: Bondtech BMG upgrade for the N series
Replies: 171
Views: 5415

Re: Bondtech BMG upgrade for the N series

Bondtech wrote:The extruder kit is now up in the webshop,

Order placed!

Go to advanced search