Search found 12 matches

by rodriguejr
Fri Feb 23, 2018 12:24 pm
Forum: Hardware
Topic: Filament run-out sensor with bond tech extruder
Replies: 2
Views: 288

Re: Filament run-out sensor with bond tech extruder

Thanks Jetguy. Much appreciated.
by rodriguejr
Fri Feb 23, 2018 10:37 am
Forum: Hardware
Topic: Filament run-out sensor with bond tech extruder
Replies: 2
Views: 288

Filament run-out sensor with bond tech extruder

Hello,

I am running my raise3d N2 Plus (in single extruder form) with a bondtech extruder. Does anyone know if there is any impediment on using the new filament run out sensor?

Regards,
Jorge
by rodriguejr
Mon Oct 09, 2017 1:48 pm
Forum: Printing Settings
Topic: Colorfabb XT-CF20 for 40h print
Replies: 20
Views: 2203

Re: Colorfabb XT-CF20 for 40h print

Hello Julia, Thanks for your post. Over the weekend I figured out new settings for XT-CF20 that now allow me to print without too much gunk on the nozzle, together with "cutting" the part to avoid the need for supports altogether. Unfortunately, overnight the throat tube got jammed by the ...
by rodriguejr
Sun Oct 08, 2017 8:30 am
Forum: Printing Settings
Topic: Colorfabb XT-CF20 for 40h print
Replies: 20
Views: 2203

Re: Colorfabb XT-CF20 for 40h print

Hi Eldrick, Thanks for the post. I have done a full print using PCMax and it looks solid. I have that backup plan if nothing else works. I was hoping to get the "Carbon fiber" look for the Air intake and rear parts (the rear is even bigger, so I will have to think how to cut it down). Rega...
by rodriguejr
Fri Oct 06, 2017 5:58 pm
Forum: Printing Settings
Topic: Colorfabb XT-CF20 for 40h print
Replies: 20
Views: 2203

Re: Colorfabb XT-CF20 for 40h print

BTW here is the PCMax print (no finishing done since I need to shorten the intake a bit). Not to bad for my first print using PCMax.

Regards,
Jorge
IMG_0461.jpg
IMG_0460.jpg
by rodriguejr
Fri Oct 06, 2017 5:55 pm
Forum: Printing Settings
Topic: Colorfabb XT-CF20 for 40h print
Replies: 20
Views: 2203

Re: Colorfabb XT-CF20 for 40h print

Hi Lami3D,

Thanks for your reply. How did you go about polishing your nozzle? Won't that remove the coating?

Regards,
Jorge
by rodriguejr
Fri Oct 06, 2017 5:32 pm
Forum: Printing Settings
Topic: Colorfabb XT-CF20 for 40h print
Replies: 20
Views: 2203

Re: Colorfabb XT-CF20 for 40h print

Hi Jetguy, Thanks again for your help. I think it is a good suggestion to remove the bottom bracket, I may try to find a way attach the part to the bike. I need to be a bit careful, since this thing is 150Kg/150HP and I cannot afford any loose parts or gluing stuff together. I am giving it another t...
by rodriguejr
Fri Oct 06, 2017 4:36 pm
Forum: Printing Settings
Topic: Colorfabb XT-CF20 for 40h print
Replies: 20
Views: 2203

Re: Colorfabb XT-CF20 for 40h print

Hi guys, Thanks for your prompt replies. @Jetguy: Thanks for your insightful comments, as always. 1) The nozzle is steel plated as recommended and I have used it just for this print. It is a 0.4mm 2) I may try the current settings for retraction with lower temperature (around 250C) with less infill ...
by rodriguejr
Fri Oct 06, 2017 10:13 am
Forum: Printing Settings
Topic: Colorfabb XT-CF20 for 40h print
Replies: 20
Views: 2203

Colorfabb XT-CF20 for 40h print

Hello, I am doing a Ducati Panigale project bike and I need to print some large parts on my Raise3D N2 Plus. I am now on my third attempt to print the Air intake (attached STL) using XT-CF20 (I have done prior prototypes using Polymaker’s PCMAX and Raise3D PLA without problems both 40h plus prints)....
by rodriguejr
Sat Sep 09, 2017 6:18 am
Forum: Hardware
Topic: Touchscreen unresponsive
Replies: 5
Views: 1408

Re: Touchscreen unresponsive

Hi all,

The problem has been fixed by replacing the touchscreen under warranty. Thanks Raise3D support.

Regards,
Jorge
by rodriguejr
Sun Sep 03, 2017 11:33 am
Forum: Hardware
Topic: Touchscreen unresponsive
Replies: 5
Views: 1408

Re: Touchscreen unresponsive

Hello Vicky, Thanks. I already did that. Waiting for support to get back to me. Meanwhile would it be possible for you to post a picture for the controller board for the touchscreeb (mine is blue, not the white color I have seen on some others). I have two empty connectors on my board that I have se...
by rodriguejr
Sun Sep 03, 2017 5:37 am
Forum: Hardware
Topic: Touchscreen unresponsive
Replies: 5
Views: 1408

Touchscreen unresponsive

Hi all, My name is Jorge and I am new to 3D printing. The reason I joined is that I am doing a Ducati Panigale motorcycle bike project (the real thing not a model) and I needed to design and print some of the "plastic" parts. I cannot say my first days with the printer were easy: 1- I was ...

Go to advanced search