Search found 56 matches

by checktest
Sat Nov 18, 2017 5:27 pm
Forum: Software
Topic: Pause at height when slicing with Simplify3D or other software
Replies: 29
Views: 3359

Re: Pause at height when slicing with Simplify3D or other software

I've been trying to figure this out as well on my Raise3D N2 for Simplify3D v4, since S3D's slicer prints my part in 33 minutes, while IdeaMaker takes 53 minutes. That's a big deal, since I'm trying to print quite a lot of these. I've tried the code below, and on layer 7 it homes X and Y, raises 50 ...
by checktest
Fri Nov 03, 2017 7:43 pm
Forum: General
Topic: STL for N2+ full build volume lattice?
Replies: 1
Views: 90

STL for N2+ full build volume lattice?

Does anyone have a link to the STL for that large yellow lattice part that's shown on the N2+ product page?
by checktest
Thu Oct 26, 2017 8:53 pm
Forum: Software
Topic: ideaMaker 3.0-beta Release Note Updated Rev. 3.0.3 2017.11.13
Replies: 107
Views: 2752

Re: ideaMaker 3.0-beta Release Note 2017.10.23

This is great! Thanks Raise3D for the continued improvements!
by checktest
Wed Sep 20, 2017 4:10 pm
Forum: General
Topic: Considering Second N2 (maybe N2 Plus?)
Replies: 3
Views: 387

Re: Considering Second N2 (maybe N2 Plus?)

So, over a year and still missing badly needed improvements like easier bed leveling, filament monitor, dedicated fan and duct for better downward cooling, fans that can turn off when not printing, or a stock extruder that doesn't grind filament and jam. That last one is sad since there's already a ...
by checktest
Wed Sep 13, 2017 9:40 pm
Forum: General
Topic: Considering Second N2 (maybe N2 Plus?)
Replies: 3
Views: 387

Considering Second N2 (maybe N2 Plus?)

I bought my current N2 in June 2016, and it works well for me. I did some basic mods, including the Bondtech extruder. I'm now considering buying another N2, or an N2 Plus, single extruder only this time. Is there any way to buy either directly from Raise3D with the Bondtech extruder upgrade already...
by checktest
Sat Apr 08, 2017 7:54 pm
Forum: Software
Topic: Filament Swap "Print"
Replies: 4
Views: 415

Re: Filament Swap "Print"

OK, thanks for that info, I just updated to touchscreen firmware 0.9.0.790 and tried it again. It still leaves a resume message on the display when the print is done, and I had thought it was locked up, but I realized the bottom tab buttons on the screen do work and I can go load another print. I'm ...
by checktest
Wed Apr 05, 2017 3:14 pm
Forum: Software
Topic: Filament Swap "Print"
Replies: 4
Views: 415

Re: Filament Swap "Print"

Yes it resumes fine normally. Had to do it 2 times last week.
by checktest
Sat Apr 01, 2017 5:35 pm
Forum: Software
Topic: Filament Swap "Print"
Replies: 4
Views: 415

Filament Swap "Print"

I'm looking to create a "print" that better automates filament changes. Basically, I'd like to run this gcode file any time I want to unload the current filament and load another color, instead of doing it manually through the screen or ideamaker. The idea is that I just start the print, g...
by checktest
Fri Feb 17, 2017 4:34 am
Forum: Hardware
Topic: Guiding tubes rubbing against top cover
Replies: 8
Views: 991

Re: Guiding tubes rubbing against top cover

I put shrink tubing over the tube, helps a lot.
by checktest
Mon Feb 13, 2017 5:48 pm
Forum: Printing Settings
Topic: Support Settings
Replies: 4
Views: 699

Re: Support Settings

You could also try changing "Vertical Offset Down Layers" from the default of 1 to 0, so there is no layer gap between the bottom of the support and the raft. You may have more difficulty getting the support off the part if you have any areas where the support bases start on the part itsel...
by checktest
Thu Feb 02, 2017 3:24 pm
Forum: Software
Topic: What exactly does "sparse connection" do? (Answered & it's probably opposite of what you think!)
Replies: 12
Views: 1681

Re: What exactly does "sparse connection" do?

Thanks Vicky for the explanation, I was also wondering what Sparse Connection did. However, that is a strange name as I imagine most people (myself included) would assume that was referring to the connection between the support material and the model. Can I suggest it either be renamed to something ...
by checktest
Mon Jan 30, 2017 3:03 pm
Forum: General
Topic: Intermittent WiFi Connection
Replies: 18
Views: 1164

Re: Intermittent WiFi Connection

Yes also fails uploading, only at the same time that it won't connect to the printer. Just won't start uploading, never fails part way through uploading.
by checktest
Sat Jan 28, 2017 5:47 pm
Forum: General
Topic: Intermittent WiFi Connection
Replies: 18
Views: 1164

Re: Intermittent WiFi Connection

Yes

Was working fine an hour ago...but now it's not again

Capture.JPG
by checktest
Sat Jan 28, 2017 4:54 pm
Forum: General
Topic: Intermittent WiFi Connection
Replies: 18
Views: 1164

Re: Intermittent WiFi Connection

IdeaMaker 2.4.0.585 and firmware 1.1.1. I also see "Version 0.8.0.501".
by checktest
Sun Jan 22, 2017 11:02 pm
Forum: General
Topic: Intermittent WiFi Connection
Replies: 18
Views: 1164

Re: Intermittent WiFi Connection

Hmm, well I'll try that and see if it helps at all.
by checktest
Sun Jan 22, 2017 8:00 pm
Forum: General
Topic: Intermittent WiFi Connection
Replies: 18
Views: 1164

Re: Intermittent WiFi Connection

Thanks. I think I've got decent wifi in that room. It's only about 30 feet from the router, without any major obstructions in the way. 60 Mbps download speed using speedtest app. About -60 dBm signal using wifi analyzer.
by checktest
Sun Jan 22, 2017 7:43 pm
Forum: General
Topic: Intermittent WiFi Connection
Replies: 18
Views: 1164

Intermittent WiFi Connection

Anybody else experience intermittent WiFi connection with their printer? Seems like half the time I go to connect or upload, it won't work. It will go from working to not working, or vice versa, even in between prints (without having reset the printer, computer, or router). Sometimes resetting those...
by checktest
Tue Jan 17, 2017 6:59 pm
Forum: Feature requests, ideas, wishes
Topic: BuildTak FlexPlate
Replies: 10
Views: 1393

Re: BuildTak FlexPlate

Isn't the N2 print area 305x305mm? Not sure how you would be wasting 35 mm per side?
by checktest
Tue Dec 27, 2016 4:41 pm
Forum: Hardware
Topic: 2ND Led Light strip and cord
Replies: 26
Views: 2238

Re: 2ND Led Light strip and cord

I used some LED strips from IKEA. They aren't exactly the same light color, but it's nice that I didn't have to mess with the printer's electronics at all as they are on their own power plug and switch.
by checktest
Tue Dec 27, 2016 4:39 pm
Forum: Hardware
Topic: insulating the heater block
Replies: 10
Views: 1124

Re: insulating the heater block

I use this, cut to size. It's somewhat stiff, so just holds itself there when put in place.

https://www.amazon.com/gp/product/B0051 ... UTF8&psc=1

Go to advanced search