Search found 76 matches

by Phife
Mon Oct 29, 2018 2:35 pm
Forum: Pro2 Series
Topic: Connecting BLTouch to control board
Replies: 2
Views: 113

Re: Connecting BLTouch to control board

Yes, disconnect the Z- and plug the black and white wires from BLTouch there. Also, you will need a compatible firmware.
by Phife
Fri Jul 20, 2018 3:56 pm
Forum: Others
Topic: Drying filament under vacuum
Replies: 18
Views: 1204

Re: Drying filament under vacuum

So how do you dry your desiccant? If I am able to recycle the oil, I don't see the water as a problem. My thought is that leaving the pump running will result in a lower moisture content in the filament and the desiccant I'm drying. Desiccant can be dried out in an oven, lots of instructions on the...
by Phife
Thu Jul 19, 2018 1:03 pm
Forum: Others
Topic: Drying filament under vacuum
Replies: 18
Views: 1204

Re: Drying filament under vacuum

This is why I pull a vacuum, shut off the valve and turn off the pump. I can hold my vacuum over night without the pump running. Dessicant is loose along the bottom of the chamber. You can get big jugs of dessicant on Amazon. I dont have these "water" problems. Also, perhaps its dryer here...
by Phife
Fri Jul 06, 2018 2:57 pm
Forum: Others
Topic: Drying filament under vacuum
Replies: 18
Views: 1204

Re: Drying filament under vacuum

I use a vacuum pump and a chamber on a heat plate set to 50c to dry my Nylon, 15micron is more than enough, I only get down to maybe 50,000micron. Works well. I also line the bottom of the chamber with Silica beads so the moisture has somewhere to go. Although I'm not sure how necessary that is.
by Phife
Mon May 07, 2018 7:44 pm
Forum: Hardware
Topic: Bltouch on Raise3d
Replies: 134
Views: 21672

Re: Bltouch on Raise3d

jvingaard wrote:Is the v1.1.6-rev1 source code with BLtouch available anywhere?

Should be here,
https://github.com/ABH10/Marlin-for-Rai ... 3D_BLTouch
by Phife
Mon Feb 19, 2018 10:51 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

@ABH, Sorry, Im a little confused. So you are saying all I need to change on the Firmware available on your Github is to change the Steps for my Dual Bondtech? Did you just use my Configuration.h file? I also changed my Z Probe Offset, and set Linear Advance to 50. I think I also setup a custom mach...
by Phife
Mon Feb 19, 2018 9:21 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

I have added the Raise3D Filament Monitor code to these compiled firmware versions: http://forum.raise3d.com/viewtopic.php?f=3&t=6244&p=25627#p25627 and to the BLTOUCH firmware here (not compiled): https://github.com/ABH10/Marlin-for-Raise3D-N-series/tree/1.1.x_Raise3D_BLTouch I didn't do t...
by Phife
Mon Feb 19, 2018 5:05 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

I have added the Raise3D Filament Monitor code to these compiled firmware versions: http://forum.raise3d.com/viewtopic.php?f=3&t=6244&p=25627#p25627 and to the BLTOUCH firmware here (not compiled): https://github.com/ABH10/Marlin-for-Raise3D-N-series/tree/1.1.x_Raise3D_BLTouch I didn't do t...
by Phife
Sun Feb 11, 2018 2:23 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

Hello, When i try to compile the 1.1.x_Raise3D_BLTouch i get an 'endif without if' in the 'configuration.h' Using Arduino 1.6.9 Board = Arduino/Genuino Mega or Mega 2560 Processor = ATmega2560 (Mega 2560) Hey Jvingaard, I got the same error when I tried to compile it. Looks like an extra "EndI...
by Phife
Fri Feb 09, 2018 9:10 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

Jetguy wrote:The LCD is sending the gcode and so that is whatever script is in that Raisepack LCD touch version. What version are you running?


I updated to the lastest raisepack when I did my firmware upgrade, so 0.9.7
by Phife
Fri Feb 09, 2018 8:16 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

Something must be broken in the Stop code, perhaps the touchscreen is waiting for a response from the firmware (MCU) to acknowledge the stop had completed? Can someone look into this? Is anyone else having this problem? On your Raise Touch LCD, under settings, do you have faststop turned on? I beli...
by Phife
Fri Feb 09, 2018 6:34 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

Hey ABH, So do you think there is any way to make a generic filament runout sensor work on these machines? I think I read somewhere that someone had got it working with a regular endstop. Surely there is a way to make this work, Can someone look into it? Ive had a chance to play with this custom fir...
by Phife
Thu Feb 08, 2018 9:58 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

I dont plan on using Raise3D's very expensive "Lack of material" sensor. I will make my own from some endstops. Would it be possible to also have the firmware allow our own Filament runout sensors? I know Marlin has a filament runout section, does this work with Raise3D printers? Thanks fo...
by Phife
Thu Feb 08, 2018 5:00 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

Hey ABH, Thanks for the offer, There are a few things that need to be setup for the BLtouch to work. I dont remember exactly what it was though. I have attached a copy of the firmware I am currently running that works with my BLtouch so maybe you can see what things were changed to make it work? I d...
by Phife
Wed Feb 07, 2018 6:01 pm
Forum: Software
Topic: LIN_ADVANCE = better extrusion control
Replies: 118
Views: 10657

Re: LIN_ADVANCE = better extrusion control

jvingaard wrote:Is there a firmware for N2Dual with BLtouch and LIN_ADVANCE


Yes please, I too am looking for N2+ Dual w/BLTouch and LIN_ADVANCE, Also, if possible to have Filament Sensor as well?
by Phife
Wed Dec 06, 2017 10:05 pm
Forum: Hardware
Topic: N2 plus completely died
Replies: 9
Views: 1253

Re: N2 plus completely died

Sounds like your ribbon cable got unplugged from the small board attache to the extruder.. Its the fabric looking flat cable at the top of your picture. Looks like its crooked in that picture, check to see if the socket came unplugged..
by Phife
Thu Nov 02, 2017 7:47 pm
Forum: General
Topic: Filament monitor
Replies: 76
Views: 14497

Re: Filament monitor

Hey guys, Ive got a workhorse Raise3D N2+, it runs daily, at least 4 hours a day, typically 2-3 15+h prints a week. Its been modded to use a PEI sheet on the bed, upgraded cooling fans, and I added BLtouch to auto level the bed. The thing Im missing and has been driving me crazy is the lack of a fil...
by Phife
Sun Aug 27, 2017 3:16 pm
Forum: General
Topic: Static (Fixed) IP Address
Replies: 2
Views: 980

Re: Static (Fixed) IP Address

Most modern routers allow you to set a static IP address for a device. Simply log into your Routers interface and find out where you can set it as static. You can usually do it from the list of connected devices, on mine I select the device from the list and set it to static IP.
by Phife
Tue May 30, 2017 10:30 pm
Forum: Hardware
Topic: Need pointers on PEI
Replies: 8
Views: 1415

Re: Need pointers on PEI

CS Hyde PEI sheet with 3M adhesive backing on my N2+, they have a size custom for the N2. Careful application of the sheet to the glass and I got no bubbles after 5-6 months of daily use. One of the best upgrades I did to the machine, most everything sticks first try, if not, I apply a little glue s...
by Phife
Sat Apr 01, 2017 5:16 pm
Forum: Feature requests, ideas, wishes
Topic: Compatibility with octoprint
Replies: 5
Views: 2097

Re: Compatibility with octoprint

The Raise3D N2 printer actually already has Octoprint Installed. You can use Putty to SSH into the machine and log in with Root and the password you set under the settings/SSH on the touchscreen. You will need to kill the Raise3D Touchscreen app that is running and then start octoprint. But then you...

Go to advanced search