Search found 12 matches

by CV-Gate
Mon Sep 24, 2018 2:34 pm
Forum: N Series
Topic: Bondtech upgrade voltage setup
Replies: 5
Views: 184

Re: Bondtech upgrade voltage setup

So it's the one below, right?
Thanks a lot for your answer.
by CV-Gate
Sun Sep 23, 2018 10:31 pm
Forum: N Series
Topic: Bondtech upgrade voltage setup
Replies: 5
Views: 184

Re: Bondtech upgrade voltage setup

Sorry but I think I don't have any other to the left. I have some below, like in this picture.

Image
by CV-Gate
Sun Sep 23, 2018 5:25 pm
Forum: N Series
Topic: Bondtech upgrade voltage setup
Replies: 5
Views: 184

Bondtech upgrade voltage setup

Hello, after installing my Bondtech extruder, I have successfully adjusted to 0.5 v the top left trimmer. The next step is "do the same with the second motor". As I have a dual extruder, I must do it but the instructions are not very helpful. Could anybody tell me what is the trimmer for t...
by CV-Gate
Sun Sep 23, 2018 5:16 pm
Forum: Pro2 Series
Topic: Filament Stepper Motors very hot - even when not printing with nozzle
Replies: 31
Views: 1435

Re: Filament Stepper Motors very hot - even when not printing with nozzle

@Vicky, I have problems with every filament.
@SchMax, does this work with the Bondtech extruder?
by CV-Gate
Sun Sep 16, 2018 7:42 pm
Forum: Pro2 Series
Topic: Filament Stepper Motors very hot - even when not printing with nozzle
Replies: 31
Views: 1435

Re: Filament Stepper Motors very hot - even when not printing with nozzle

Hello, any news on this? When could we expect the new firmware to be released? I'm having this same issue. Removing the cover works sometimes but if the printer is working for some hours it will air print for sure.
by CV-Gate
Tue Sep 11, 2018 9:00 am
Forum: General
Topic: Struder feeder gets blocked
Replies: 12
Views: 811

Re: Struder feeder gets blocked

Hi Rogman, yes, I have an Olsson Ruby nozzle installed. Still waiting for the Bondtech here, though. It's taking very long... Thanks for your answer.
by CV-Gate
Fri Sep 07, 2018 2:32 pm
Forum: General
Topic: Struder feeder gets blocked
Replies: 12
Views: 811

Re: Struder feeder gets blocked

No, unfortunately, I'm still having the issue.
by CV-Gate
Sun Aug 26, 2018 6:59 pm
Forum: General
Topic: Struder feeder gets blocked
Replies: 12
Views: 811

Re: Struder feeder gets blocked

Hi again, I pre-ordered the Bondtech extruder, I'll have it in a couple of weeks hopefully. Meanwhile, I'd like to nail down the issue a little more as I wouldn't like to inherit the problem if the extruder is not the real cause. This is my first printer and I'm not sure if this is an issue but I th...
by CV-Gate
Wed Aug 15, 2018 11:59 am
Forum: General
Topic: Struder feeder gets blocked
Replies: 12
Views: 811

Re: Struder feeder gets blocked

Another question, I'm thinking about upgrading the extruder to the Bondtech one. Is it worth?
by CV-Gate
Mon Aug 13, 2018 2:20 am
Forum: General
Topic: Struder feeder gets blocked
Replies: 12
Views: 811

Re: Struder feeder gets blocked

Thanks a lot, Prop-Fiction. I couldn't test it too much yet but it seems to be working excepting for TPU (Flexismart). It's impossible for me to load and extrude more than 5 cm of filament until the gear loses grip and gets blocked. Did you any time succeed using flexible filaments?
by CV-Gate
Sun Aug 05, 2018 12:28 pm
Forum: General
Topic: Struder feeder gets blocked
Replies: 12
Views: 811

Re: Struder feeder gets blocked

Thanks Vicky.
by CV-Gate
Fri Aug 03, 2018 9:41 pm
Forum: General
Topic: Struder feeder gets blocked
Replies: 12
Views: 811

Struder feeder gets blocked

Hi all, I'm new to the forum and almost new to 3d printing. I own a Raise3D N2 Plus that has been working flawlessly for some time. The other day, the extruder feeder was blocked and I found the printer just printing in the air. This has been happening once in a while since then but right now, it ge...

Go to advanced search