Search found 3771 matches

by Vicky@Raise3D
Sun Jul 22, 2018 8:34 pm
Forum: Pro2 Series
Topic: Right Extruder Printing
Replies: 1
Views: 2

Re: Right Extruder Printing

As Pro2 has auto-lifting system, you can directly slice a file using only one side. The other side won't affect printing as it will lift up when the other one is printing. If you want to adjust the physical height of the two hot-end, here is the instruction: https://cdn.shopify.com/s/files/1/1069/48...
by Vicky@Raise3D
Sun Jul 22, 2018 8:24 pm
Forum: Hardware
Topic: Loading filament doesn't stop!
Replies: 2
Views: 26

Re: Loading filament doesn't stop!

You mean even you finish the Filament Loading guiding process, press OK and back to other pages, the feeding gear is still rotating after a few minutes?
Does filament feeding and stop work properly during printing on your printer?
by Vicky@Raise3D
Sun Jul 22, 2018 8:20 pm
Forum: Pro2 Series
Topic: Nozzle use on touch screen
Replies: 9
Views: 153

Re: Nozzle use on touch screen

No matter an extra option besides current layer, current height, shows current nozzle or an different color nozzle icon should can meet you meets.
Is that because it is not obvious to see which nozzle is printing currently during printing, so that you are asking for this feature?
by Vicky@Raise3D
Sat Jul 21, 2018 1:49 am
Forum: Software
Topic: Display problem with Ubuntu 16.04 and ideaMaker 3.1.7 64-bit
Replies: 3
Views: 54

Re: Display problem with Ubuntu 16.04 and ideaMaker 3.1.7 64-bit

Would you like to advise the following information:
1. The type of your GPU
2. Resolution of your monitor
3. Version number of your Ubuntu system
by Vicky@Raise3D
Sat Jul 21, 2018 12:13 am
Forum: Hardware
Topic: N2 Touchscreen not reacting to touch on it's left side
Replies: 3
Views: 270

Re: N2 Touchscreen not reacting to touch on it's left side

It might be highly likely some hardware issue for the touching function. Which means it is still a broken screen.
by Vicky@Raise3D
Sat Jul 21, 2018 12:10 am
Forum: General
Topic: Temperature always on
Replies: 1
Views: 42

Re: Temperature always on

Will it be a little dangerous that if people forget to start a new print after one print done, and let the heating components stay at high temperature for very long time, like several days?
by Vicky@Raise3D
Sat Jul 21, 2018 12:06 am
Forum: Software
Topic: Z-hop before printing next layer - with random layer start point
Replies: 1
Views: 19

Re: Z-hop before printing next layer - with random layer start point

We don't have similar function currently in ideaMaker now.
by Vicky@Raise3D
Fri Jul 20, 2018 11:56 pm
Forum: General
Topic: Stops extruding after first Shell
Replies: 28
Views: 2278

Re: Stops extruding after first Shell

Do you mean that you can push out the filament to continue extruding easily after no extruding?
Which means either the gear is too far to bearing or the teeth of gear is washed.
by Vicky@Raise3D
Fri Jul 20, 2018 11:52 pm
Forum: Pro2 Series
Topic: Filament change very difficult, tips?
Replies: 7
Views: 72

Re: Filament change very difficult, tips?

May I ask a picture of your tubes?
by Vicky@Raise3D
Fri Jul 20, 2018 11:34 pm
Forum: Pro2 Series
Topic: Nozzle use on touch screen
Replies: 9
Views: 153

Re: Nozzle use on touch screen

"Active" means whether the part of the print goes out properly?
by Vicky@Raise3D
Fri Jul 20, 2018 11:30 pm
Forum: Hardware
Topic: Replacement Board, Serial Error: No Such Device or Adress
Replies: 5
Views: 122

Re: Replacement Board, Serial Error: No Such Device or Adress

The old board with drivers can work without error? And all 5 directions can be controlled by screen properly?
Then might be something wrong with the new board.
by Vicky@Raise3D
Fri Jul 20, 2018 11:11 pm
Forum: General
Topic: Y noise
Replies: 1
Views: 45

Re: Y noise

SuperLube with PTFE type will be more recommended.
by Vicky@Raise3D
Fri Jul 20, 2018 11:08 pm
Forum: Software
Topic: Ideamaker wipe tower coordinates
Replies: 3
Views: 48

Re: Ideamaker wipe tower coordinates

1.png
4.png
3.png
2.png
by Vicky@Raise3D
Fri Jul 20, 2018 10:56 pm
Forum: General
Topic: Bad quality of impression in some areas and noise
Replies: 9
Views: 234

Re: Bad quality of impression in some areas and noise

I will suggest you to try to calibrate the bed levelness until it fit 0.2mm feeler gauge.

Attached one 0.05mm layer height print test for you.
by Vicky@Raise3D
Fri Jul 20, 2018 10:10 pm
Forum: Software
Topic: Stop heating unused extruder on Pro2
Replies: 4
Views: 55

Re: Stop heating unused extruder on Pro2

As far as I known, we don't move the feeding gear backward when nozzle jog up. It is not the same as nozzle retraction, as when nozzle retraction, the nozzle does not always move up/
by Vicky@Raise3D
Fri Jul 20, 2018 9:55 pm
Forum: Printing Settings
Topic: Retraction Settings?
Replies: 3
Views: 59

Re: Retraction Settings?

I will suggestion to increase once a little bit, like 5-10% more than last try to see whether it helps.
by Vicky@Raise3D
Fri Jul 20, 2018 9:40 pm
Forum: Software
Topic: Trying to add new filament to IdeaMaker
Replies: 3
Views: 52

Re: Trying to add new filament to IdeaMaker

That's true. As the scroll bars in Windows are more obvious to be seen compared with Mac
by Vicky@Raise3D
Fri Jul 20, 2018 8:09 am
Forum: Software
Topic: Gcode preview looks wrong in Ubuntu
Replies: 13
Views: 2916

Re: Gcode preview looks wrong in Ubuntu

Would you like to advise the following information:
1. The type of your GPU
2. Resolution of your monitor
3. Version number of your Ubuntu system
by Vicky@Raise3D
Fri Jul 20, 2018 6:57 am
Forum: Hardware
Topic: Hardened nozzle 0.4 mm
Replies: 2
Views: 57

Re: Hardened nozzle 0.4 mm

Shoot an email to sales@raise3d.com. Our sales team will try their best to help.
by Vicky@Raise3D
Fri Jul 20, 2018 6:51 am
Forum: General
Topic: printer only prints on lower left corner help!!!
Replies: 2
Views: 71

Re: printer only prints on lower left corner help!!!

Manual control for X direction on screen doesn't too? But Y direction works fine?
If so, would you like ask you to try swap the stepper drivers to see the difference.

Go to advanced search