Search found 25 matches

by claytony565
Thu Nov 08, 2018 9:36 pm
Forum: Pro2 Series
Topic: Pro2 Temperature Fluctuations/Jams
Replies: 11
Views: 455

Re: Pro2 Temperature Fluctuations/Jams

Check the red and white cables going to the thermistor coming out of the green terminal blocks on the extruder board. If you look at the picture you can see in the left terminal that the white wire crosses over the top of the red wire (this was before I fixed it) and very randomly the wires would sh...
by claytony565
Thu Nov 08, 2018 9:17 pm
Forum: Software
Topic: Major Update & Improvements for Pro2 and N Series
Replies: 33
Views: 3215

Re: Major Update & Improvements for Pro2 and N Series

I just did all of the updates and now the holes on my parts are out of round? Is there some kind of offset that changed? Would you like to share the .idea, .gcode and .data files with us to test? It turns out it was a broken coupler, it just so happened to be at the same time I had done the updates.
by claytony565
Fri Nov 02, 2018 1:05 pm
Forum: Software
Topic: Major Update & Improvements for Pro2 and N Series
Replies: 33
Views: 3215

Re: Major Update & Improvements for Pro2 and N Series

I just did all of the updates and now the holes on my parts are out of round? Is there some kind of offset that changed?
by claytony565
Tue Jul 24, 2018 8:14 pm
Forum: Pro2 Series
Topic: Cold nozzles reading 240° C
Replies: 86
Views: 4692

Re: Cold nozzles reading 240° C

I had the same problems on my Pro2. I ended up re-seating the thermistor cables inside of the top green terminal boxes. For whatever reason they were installed with one cable crossed over the other one. Every once in a while the printer would shift just right and cause those two wires to come in con...
by claytony565
Fri Jul 13, 2018 4:44 pm
Forum: General
Topic: Annoying Sound on my Pro2
Replies: 8
Views: 573

Re: Annoying Sound on my Pro2

Tech support says they believe it is a broken coupler and they are sending me a new one. I suspect I will receive it next week and replace it then. Interesting. Sounds like I will have to look more closely at nine here, Thanks for the response. I finally received the replacement coupler today and i...
by claytony565
Mon Jul 02, 2018 3:47 pm
Forum: General
Topic: PETG on Pro2
Replies: 6
Views: 596

Re: PETG on Pro2

Just finished a test cube with the standard PETG settings for the Pro2. Came out pretty well, much better than my print on the N2. the layers are very well bonded, there is some light stringing between pieces but not bad. I did not use a raft and it stuck to the buildtak very well with the bed dista...
by claytony565
Mon Jul 02, 2018 1:42 pm
Forum: General
Topic: End of filament sensor
Replies: 5
Views: 736

Re: End of filament sensor

Hello everyone, i ordered an end of filament sensor for my N2 plus months ago and i have yet to receive it. I now see the pro 2 is being shipped with this sensor. What gives? Am i the only one not getting the sensor or is it everyone? I submitted a ticket and i get some vague reply that said i woul...
by claytony565
Mon Jul 02, 2018 1:39 pm
Forum: General
Topic: PETG on Pro2
Replies: 6
Views: 596

Re: PETG on Pro2

I am currently running some tests on it now, I just tried on my N2+ for the first time last week and I had very weak layers and my outer shells actually peeled right off. I will let you know what works for PETG on the Pro2 once I can get it dialed in.
by claytony565
Fri Jun 29, 2018 8:23 pm
Forum: Hardware
Topic: Odd Print Failures Pro2
Replies: 3
Views: 423

Re: Odd Print Failures Pro2

Hi guys, I'm all of a sudden running into printing issues with my Pro2, no idea what could be causing them. I've had several long prints fail on me with settings that have worked in the past, I've attached an image of the most recent failure. IMG_0940.JPG Honestly can't tell if there is nozzle drag...
by claytony565
Fri Jun 29, 2018 8:01 pm
Forum: General
Topic: Annoying Sound on my Pro2
Replies: 8
Views: 573

Re: Annoying Sound on my Pro2

Thanks for the info. I just put in a support ticket. Having a similar sound on mine as well. Do you mind updating this when you have found a solution? Thanks. Tech support says they believe it is a broken coupler and they are sending me a new one. I suspect I will receive it next week and replace i...
by claytony565
Wed Jun 27, 2018 6:44 pm
Forum: General
Topic: Annoying Sound on my Pro2
Replies: 8
Views: 573

Re: Annoying Sound on my Pro2

My first guess would be a failed motor to shaft coupler. If the motor was even slightly misaligned, these couplers fail in short order (days or weeks) because every rotation of the shaft fatigues the already thin aluminum. http://forum.raise3d.com/viewtopic.php?t=1281 Thanks for the info. I just pu...
by claytony565
Wed Jun 20, 2018 12:41 pm
Forum: General
Topic: Pro2 Overheating.
Replies: 8
Views: 825

Re: Pro2 Overheating.

Vicky@Raise3D wrote:I will recommend that not using the printer temporarily until we figure out the root cause and fix it. Or overheating will be damage.


My biggest concern is the lack of an error when there is a 150+ temperature reading swing. It shouldn't compensate for that by immediately starting to heat up.
by claytony565
Tue Jun 19, 2018 1:17 pm
Forum: General
Topic: Pro2 Overheating.
Replies: 8
Views: 825

Re: Pro2 Overheating.

Please submit a support ticket at help.raise3d.com. We want to get more detail information about the current temperature issue you are meeting with. Have you ever tried with move the extruder around manually with nozzles not heating and check whether the temperature values change on screen or not. ...
by claytony565
Mon Jun 18, 2018 2:41 pm
Forum: General
Topic: Pro2 Overheating.
Replies: 8
Views: 825

Pro2 Overheating.

Thought I would give the community a heads up, I just purchased a Pro2 for work and we have had it for just under a month. We are having some serious issues with the nozzles overheating. This has happened a few times where the print temperature shown on the touchscreen has dropped drastically and st...
by claytony565
Fri Jun 15, 2018 6:00 pm
Forum: General
Topic: Calibration PRO 2
Replies: 4
Views: 1071

Re: Calibration PRO 2

Bed leveling is pretty much the same, I think there are a few less points of contact and some of the bolts seem to be more secure. The bed plate is removable though so that is nice. And they do ship the Pro2 models with a calibration print on the plate which is actually pretty reassuring. Have been ...
by claytony565
Thu Jun 14, 2018 6:18 pm
Forum: General
Topic: Raise3D Pro2 initial impression
Replies: 11
Views: 2446

Re: Raise3D Pro2 initial impression

Have you had any problems so far? I am having issues with heating that are eerily similar to the N series printer ribbon cable fiasco. I know they do to use the same cable but I am experiencing the same erratic temperature problems, except this time I get no error just burnt filament! If you could,...
by claytony565
Thu Jun 14, 2018 3:53 pm
Forum: General
Topic: Raise3D Pro2 initial impression
Replies: 11
Views: 2446

Re: Raise3D Pro2 initial impression

Have you had any problems so far? I am having issues with heating that are eerily similar to the N series printer ribbon cable fiasco. I know they do to use the same cable but I am experiencing the same erratic temperature problems, except this time I get no error just burnt filament!
by claytony565
Thu Jun 14, 2018 2:28 pm
Forum: User's Gallery
Topic: First Month of Printing
Replies: 4
Views: 911

Re: First Month of Printing

Yes, just wanted to see if it was possible. I also scaled the entire thing down so the hole isn't necessarily fit for a standard fastener. I'm new with the Raise3d N2 plus printer (1 week of practice) and I'd really like to know what parameters did you use to get the bolt-nut system working. I have...
by claytony565
Fri Jun 08, 2018 1:14 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 83
Views: 7555

Re: Filament Run-out Sensor Add-on

UPDATE: I plugged it in to the MCB upside down like a doofus. In order to best explain to others to prevent the mistake. I think you are saying you flipped the EXP3 connector with the red and back wires. It is not "keyed" and can be flipped around and still plug in- but when doing so- no ...
by claytony565
Thu Jun 07, 2018 6:05 pm
Forum: Hardware
Topic: Filament Run-out Sensor Add-on
Replies: 83
Views: 7555

Re: Filament Run-out Sensor Add-on

UPDATE: I plugged it in to the MCB upside down like a doofus.

Go to advanced search