Search found 1230 matches

by walshlg
Wed Aug 16, 2017 4:19 pm
Forum: Printing Software
Topic: Travel moves through open parts
Replies: 10
Views: 177

Re: Travel moves through open parts

no, add on a throwaway piece, eg a cylinder outside the build piece, also select a point on that for force layer change.
by walshlg
Mon Aug 07, 2017 5:02 pm
Forum: General
Topic: Big Retraction Problems!
Replies: 1
Views: 133

Re: Big Retraction Problems!

Hi, I never retract more than about 1.5 mm. I think you might be printing too hot and that is causing excessive oozing. You can also add extra material on restart to counteract the loss of material on retraction.
by walshlg
Fri Jul 21, 2017 4:32 pm
Forum: Hardware
Topic: Brand new V2 Hot End clogged with Ninjaflex Cheetah flexible filament
Replies: 13
Views: 234

Re: Brand new V2 Hot End clogged with Ninjaflex Cheetah flexible filament

If you had an isolation tube clog then you can sometimes get it pushed out but with a layer of plastic still sticking to the sides- to check and to clear this, take off the nozzle, heat it up, I use 250C and let sit for an hour. Then push the 1mm rod through repeatedly -> in the top and out the bott...
by walshlg
Fri Jul 21, 2017 4:25 pm
Forum: Printing Software
Topic: Retract filament at end of print?
Replies: 11
Views: 186

Re: Retract filament at end of print?

FWIW -> I never unload filament unless I need to. Some filaments, like the tpu, I unload before every single print, even if its only been idle for 5 min because doing so improves the chance of a good print. an advantage of not unloading or even retracting: IMHO the biggest single major PITA with pri...
by walshlg
Thu Jul 20, 2017 3:56 pm
Forum: Hardware
Topic: Brand new V2 Hot End clogged with Ninjaflex Cheetah flexible filament
Replies: 13
Views: 234

Re: Brand new V2 Hot End clogged with Ninjaflex Cheetah flexible filament

Jetguy - IF I make these lined guide tubes, should I switch them out when I go back to regular filaments?
by walshlg
Thu Jul 20, 2017 3:54 pm
Forum: User's Gallery
Topic: Single extruder multiple color using the Mosaic Palette
Replies: 79
Views: 3809

Re: Single extruder multiple color using the Mosaic Palette

So cool. So are they adding an option for more colors, 6, 8??
by walshlg
Thu Jul 20, 2017 2:55 pm
Forum: Hardware
Topic: Brand new V2 Hot End clogged with Ninjaflex Cheetah flexible filament
Replies: 13
Views: 234

Re: Brand new V2 Hot End clogged with Ninjaflex Cheetah flexible filament

fwiw, I found that the brass 400um nozzles worked but the steel coated ones would not work with ninja.

Jetguy- this would be a great place to use that super-slick ptfe tubing!
by walshlg
Wed Jul 19, 2017 12:40 pm
Forum: Hardware
Topic: Touchscreen freezes
Replies: 12
Views: 221

Re: Touchscreen freezes

Also, The USB cable hangs straight down from the boards. Raise suggested: Check and hot glue it in place both on the lcd controller board and on the main board. I know, doesn't sound very elegant but it works.
by walshlg
Wed Jul 19, 2017 12:37 pm
Forum: Software
Topic: flow rate
Replies: 1
Views: 58

flow rate

please add back to ideamaker a setting for general flow rate. My new nozzles seem to under-extrude by a little and it would be helpful to add this adjustment back to the menu.
by walshlg
Wed Jul 19, 2017 12:35 pm
Forum: Printing Software
Topic: Adjust flow rate, how??
Replies: 2
Views: 123

Re: Adjust flow rate, how??

Thanks, that'll do it!
by walshlg
Wed Jul 19, 2017 12:09 pm
Forum: Printing Settings
Topic: Print settings using a 0.8mm nozzle
Replies: 8
Views: 173

Re: Print settings using a 0.8mm nozzle

with vase mode, there is no retraction
by walshlg
Wed Jul 19, 2017 1:58 am
Forum: Printing Settings
Topic: Print settings using a 0.8mm nozzle
Replies: 8
Views: 173

Re: Print settings using a 0.8mm nozzle

vase mode is nice and very smooth
by walshlg
Tue Jul 18, 2017 4:46 pm
Forum: Printing Settings
Topic: Raft and bottom layers problem
Replies: 11
Views: 200

Re: Raft and bottom layers problem

I have seen that too and just ignored it. I think you may want to message Vicky about this

May I suggest trying to print with a slower raft pint speed
by walshlg
Tue Jul 18, 2017 4:42 pm
Forum: Printing Settings
Topic: Print settings using a 0.8mm nozzle
Replies: 8
Views: 173

Re: Print settings using a 0.8mm nozzle

Well I can help on the holes, I had the same problem with my retraction tests. Basicly, with the big nozzle, retraction doesn't quite work right. You get around it by putting in a value in "add after retraction" IIRC it was about 1.2mm for me using petg. I also found that slowing down and ...
by walshlg
Tue Jul 18, 2017 4:35 pm
Forum: User's Gallery
Topic: Single extruder multiple color using the Mosaic Palette
Replies: 79
Views: 3809

Re: Single extruder multiple color using the Mosaic Palette

hah ha haaa that is a great print!
by walshlg
Tue Jul 18, 2017 4:33 pm
Forum: Hardware
Topic: Z axis problem
Replies: 6
Views: 168

Re: Z axis problem

hmm post some pics and I'll take a look, Vicky is also a great help.
by walshlg
Tue Jul 18, 2017 4:29 pm
Forum: Hardware
Topic: Board error1 and home position
Replies: 32
Views: 403

Re: Board error1 and home position

So you are saying that once you have removed the hot end you need to turn on the printer and have it start to heat the hot end until you smell the heat in order to loosen the set screws? The plastic cover that goes over the extruder board does cause the thermocouple wires to kink. Let me clarify: I...
by walshlg
Tue Jul 18, 2017 4:16 pm
Forum: Printing Software
Topic: Adjust flow rate, how??
Replies: 2
Views: 123

Adjust flow rate, how??

OK I think I have looked all over I can't see where to adjust the overall flow/ feed for anything but first layer, fill.

Am I missing something, I need to increase my overall flow by 2-5%.
by walshlg
Mon Jul 17, 2017 3:08 am
Forum: Hardware
Topic: Board error1 and home position
Replies: 32
Views: 403

Re: Board error1 and home position

getting out the thermocouple is a TOTAL PITA! you need an M1.5, brand new or atleast hardened steel, Allen wrench. You will also need to heat up the block to get the thermocouple out if there is the slightest contamination in the thermocouple hole (there always is). It is really tough to twist that ...
by walshlg
Mon Jul 17, 2017 2:51 am
Forum: Printing Software
Topic: Bug? in iM
Replies: 10
Views: 149

Re: Bug? in iM

one thing to check is for and remove double verts (if using blender or another mesh type program). Faces too close are also a source of errors as the slicer thinks they overlap

Go to advanced search