Search found 1165 matches

by walshlg
Tue Jun 27, 2017 2:55 pm
Forum: Printing Settings
Topic: Polyflex gear skipping and settings for Bend Lay and Poly flex
Replies: 5
Views: 66

Re: Polyflex gear skipping and settings for Bend Lay and Poly flex

Nice Tutorial, Jetguy. THis should be stickied or added to FAQ imho. One additional step, if pulling back results in an isolation tube/ heatbreak clog, is to remove the nozzle and hotend - (leaving the heater and thermocouple in place!) heat it up and leave it hot for an hour, then push the cleaning...
by walshlg
Tue Jun 27, 2017 1:12 pm
Forum: Hardware
Topic: Request to enable FAN0 output on breakout board
Replies: 7
Views: 56

Re: Request to enable FAN0 output on breakout board

good idea, adding another cooling fan may be quite useful
by walshlg
Mon Jun 26, 2017 3:40 pm
Forum: General
Topic: Has Agua Net Changed its Formula
Replies: 1
Views: 34

Re: Has Agua Net Changed its Formula

the purple cans work and the other colors don't IIRC
by walshlg
Mon Jun 26, 2017 3:29 pm
Forum: General
Topic: Black hard goop on Nozzle and Heater Body
Replies: 9
Views: 167

Re: Black hard goop on Nozzle and Heater Body

be extra careful of silicone grease - if you get it on your build plate it will never wash off and nothing will ever stick to that spot
by walshlg
Mon Jun 26, 2017 3:27 pm
Forum: General
Topic: 270°C or higher
Replies: 7
Views: 66

Re: 270°C or higher

Also need the top cover on
by walshlg
Fri Jun 23, 2017 1:15 pm
Forum: Feature requests, ideas, wishes
Topic: pivot changing
Replies: 6
Views: 113

Re: pivot changing

One trick for placing supports is to add them from the underneath view - looking up at the model.
by walshlg
Wed Jun 21, 2017 4:27 pm
Forum: Printing Settings
Topic: Ninjaflex Tips ?
Replies: 3
Views: 59

Re: Ninjaflex Tips ?

the biggest additional help is 1) place filament on a holder above the printer and try not to use ANY guide tubes except a short length at the top of the cold end 2) unload, trim the kink and reload IMMEDIATELY before printing, letting it sit for even 5 minutes after loading will result in a kink in...
by walshlg
Wed Jun 21, 2017 3:45 pm
Forum: User's Gallery
Topic: Wall of shame prints (print failures)
Replies: 18
Views: 1216

Re: Wall of shame prints (print failures)

woofy wrote:So who wants to take a guess at what failed.


edge curl?
by walshlg
Tue Jun 20, 2017 4:00 pm
Forum: Printing Software
Topic: Setting Changes Aligned with Nozzle Size?
Replies: 5
Views: 94

Re: Setting Changes Aligned with Nozzle Size?

I decrease speed some eg default from 50 down to 40
by walshlg
Mon Jun 19, 2017 1:46 pm
Forum: Hardware
Topic: This the right tool for cleaning material off Nozzel and hotend? Dremmel clone with wire disc brush
Replies: 3
Views: 91

Re: This the right tool for cleaning material off Nozzel and hotend? Dremmel clone with wire disc brush

search for insulating hotend, I use a ceramic "tape" / paper and cover with kapton tape
by walshlg
Mon Jun 19, 2017 1:40 pm
Forum: General
Topic: Tech support unable to advise, printing ceases after 30-40 mins
Replies: 21
Views: 216

Re: Tech support unable to advise, printing ceases after 30-40 mins

make sure that the heater and thermocouples are held tightly. Also may want to take some fine wire and wire a thermocouple directly to the groove of the threads at the top of the nozzle.

I've also had this happen from bad filament where the diameter slowly changes over 10's of meters.
by walshlg
Sat Jun 17, 2017 7:52 pm
Forum: Others
Topic: Silly: YouTube vid of drunk guys trying to remove support from a helmet?
Replies: 2
Views: 83

Silly: YouTube vid of drunk guys trying to remove support from a helmet?

OK totally silly request but a few years ago there was a vid of 2 guys removing stuck on support from the inside of a full sized iron man helmet. It was taking hours and they kept drinking and getting frustrated and almost destroyed the print trying to get the support out. I can't seem to find the v...
by walshlg
Sat Jun 17, 2017 7:45 pm
Forum: Printing Settings
Topic: Print problems with TPU on N2 - Completely stumped!
Replies: 5
Views: 103

Re: Print problems with TPU on N2 - Completely stumped!

feeder tube drag had me stumped for a month - no feeder tube if possible I just hung up a loop of wire over the bed to keep the filament feeding. Also, unload , trim reload and print immediately. If it sits clamped down in the cold end for a minute, the filament will pick up a kink. It also seemed t...
by walshlg
Sat Jun 17, 2017 7:34 pm
Forum: Software
Topic: Different Infill percentage
Replies: 2
Views: 49

Re: Different Infill percentage

I sometimes model in support and fill. I really do prefer the tree type support option that s3d has when having to fill a large area, like the inside of a helmet but you have to model it by hand for now.
by walshlg
Sat Jun 17, 2017 7:31 pm
Forum: User's Gallery
Topic: Another Baby Groot
Replies: 7
Views: 576

Re: Another Baby Groot

wow great finish too!
by walshlg
Sat Jun 17, 2017 7:30 pm
Forum: Hardware
Topic: This the right tool for cleaning material off Nozzel and hotend? Dremmel clone with wire disc brush
Replies: 3
Views: 91

Re: This the right tool for cleaning material off Nozzel and hotend? Dremmel clone with wire disc brush

I still worry that will damage the aluminum. I just get it hot and wipe off with paper towels then finally a cloth rag. I also replace nozzles every 6-12 months. One reason I insulate the hotblock is that when I really make a mess, I just peel off the tape and insulation and do it again.
by walshlg
Sat Jun 17, 2017 7:26 pm
Forum: Hardware
Topic: Touch screen stops working after few minutes
Replies: 8
Views: 123

Re: Touch screen stops working after few minutes

You don't really need to ground the machine, ground floating is OK but you need to touch the end of one of one of the uncoated screws that hold the plexiglass on before the touch screen. FWIW one spot on my touch screen is dead. See if there are parts that work and parts that don't. I should probabl...
by walshlg
Sat Jun 17, 2017 7:18 pm
Forum: General
Topic: Dual head print shifted in Y
Replies: 14
Views: 206

Re: Dual head print shifted in Y

no its much easier than that. Go into ideamaker and use "freecut" to slice off the top few layers to print. you should also add wipewall, you may want to print only 4 at a time to test. My best guess is that your z on the nozzles is off, one is much lower, put a piece of paper underneath a...
by walshlg
Fri Jun 16, 2017 4:12 pm
Forum: Printing Software
Topic: best print setting to print nylon and polyflex filament with 0.2mm nozzle
Replies: 1
Views: 72

Re: best print setting to print nylon and polyflex filament with 0.2mm nozzle

you might not be able to print a flexible with that tiny nozzle, you are the first I've heard try it, most go with a wider nozzle if anything. Let us know what you find out.

Go to advanced search