Search found 13 matches

by billbucket
Fri May 25, 2018 3:12 am
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

Would you like to try the testing gcode file we provide on your printer? We are currently not sure about the root reason about the issue your meet. Maybe it is due to something wrong inside start code, so that we want to ask you to help test our code. For the Z axis dropping height in end code, we ...
by billbucket
Wed May 23, 2018 11:29 pm
Forum: Software
Topic: Touchscreen Firmware 0.9.9 Release Note 2018.5.17
Replies: 42
Views: 618

Re: Touchscreen Firmware 0.9.9 Release Note 2018.5.17

No ma'am. The Bed does not stop at the stopped height, the bed moves down to about the middle of the available Z. Almost as if it were intended to offer our hands more room to remove the model from the bed. I have the same observation. It is 4 inches lower than before the last update. My Pro2 moves...
by billbucket
Wed May 23, 2018 4:21 am
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

Really, for the Pro2 series when we got to hard questions was, what actual motion control firmware runs on the motion board and the answer was custom firmware started from scratch- and then we get the new machine and new firmware, and it has the same old Marlin bug as the current firmware? I find t...
by billbucket
Wed May 23, 2018 4:19 am
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

Would you like to help export log and share with me? Or maybe directly open a support ticket from our support system. We are wondering whether it is due to any hardware issue. And if you switch the nozzles to carry out loading and unloading several times, the lifting can always work properly or som...
by billbucket
Mon May 21, 2018 4:37 am
Forum: General
Topic: Pro2 Left vs. Right Extruder raise distance
Replies: 2
Views: 156

Re: Pro2 Left vs. Right Extruder raise distance

Mine is not nearly that asymmetrical. The difference is nearly impossible to determine visually, but measuring shows less than 0.5 mm difference.
by billbucket
Mon May 21, 2018 4:25 am
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

This is still happening. On a fresh start today, the printer never lowers the right nozzle to begin printing from it. It's apparently specified in the g-code to do so (the T1 command), but there isn't any documentation I can find that would confirm that. ;Sliced by ideaMaker 3.1.7.1850, 2018-05-20 2...
by billbucket
Sat May 19, 2018 10:38 pm
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

The nozzle leveling system should be triggered before printing in normal case. Isn't this part in the closed source start-up section? The starting g-code for the Pro2 appears to be largely ignored or at least made irrelevant by the secret sauce the machine runs behind the scenes. I would love to be...
by billbucket
Wed May 16, 2018 6:30 pm
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

preheating nozzle to high temperature is for in case the nozzle lifts at low temperature Actually another idea occurs to me. Why not do this interrupt style like the runout sensor does? If there is a g-code request to lift a cold extruder, interrupt, heat the extruder, then perform the lift. Does t...
by billbucket
Wed May 16, 2018 4:33 pm
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

Want to dig out why the nozzle lifting function doesn't work first. The reason why I asked whether you had edited the nozzle temperature before print started was I wanted to confirm whether after preheating completes before print starts when the nozzle should be switched to lift up at least once, t...
by billbucket
Wed May 16, 2018 6:42 am
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

Want to double confirm with you whether you have edit nozzle temperature values before print starts? And would you like to mail the version number of your firmwares on touchscreen to support@raise3d.com. (As your account is newly registered, the PM function cannot work properly for by now.) I have ...
by billbucket
Tue May 15, 2018 4:39 pm
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Re: Is my Pro2 preheating correctly?

in case the nozzle lifts at low temperature that filament inside not being melt properly which may do hard to nozzle tip. Actually for both nozzles and heated bed, they are heating at the same time. Just the data feedback has an sequence. That actually raises another question, no pun intended. Does...
by billbucket
Mon May 14, 2018 7:16 pm
Forum: General
Topic: Is my Pro2 preheating correctly?
Replies: 19
Views: 1229

Is my Pro2 preheating correctly?

When my Pro2 heats up before a print where a single extruder is being used, it waits for both extruders to heat up, then (only once both are heated) it starts heating the bed. From the exported gcode, I wouldn't expect this. Here is the default generated startup section, with my comments added M221 ...
by billbucket
Tue May 08, 2018 7:40 pm
Forum: General
Topic: First Pro2 Print
Replies: 11
Views: 2288

Re: First Pro2 Print

@Jetguy For the Pro2, the machine version is 0.9.8.1652 and the firmware version is 0-0-31.

Go to advanced search